Do These EMS-4 Setup Values Look Right?
#1
Elite Member
Thread Starter
iTrader: (12)
Join Date: Jan 2007
Location: Hermosa Beach, CA
Posts: 2,573
Total Cats: 12
Do These EMS-4 Setup Values Look Right?
This is for a 94' running off the CAS. Running sequential fuel (stock injectors), wasted spark with stock coils.
I am unsure about injector phasing, ignition phasing, and wheel teeth. Can someone verify?
Thanks!
I am unsure about injector phasing, ignition phasing, and wheel teeth. Can someone verify?
Thanks!
#2
Elite Member
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,892
Total Cats: 399
i'm only qualified to say anything when I'm working on my car and it's fresh in my head and I have my notebook open, otherwise I forget things fast, so that said...
I assume "coil xB" is the wasted spark version of "coil x"? If so, you only have tooth 0 & 1 accounted for. You need to have 2 & 3 in there, otherwise nothing will happen ignition wise on those 2 teeth. As you have it, both coils fire on teeth 0 & 1 at the same time, and 0 & 1 only, ut oh.
Your fuel teeth don't follow the ignition firing order of 1,3,4,2. As is, you are firing the injectors in this order: 1,3,2,4. The engine will run, but...
I think on my series 1, the fuel teeth should be 2 teeth off the ignition teeth (360crank degrees off).
I assume "coil xB" is the wasted spark version of "coil x"? If so, you only have tooth 0 & 1 accounted for. You need to have 2 & 3 in there, otherwise nothing will happen ignition wise on those 2 teeth. As you have it, both coils fire on teeth 0 & 1 at the same time, and 0 & 1 only, ut oh.
Your fuel teeth don't follow the ignition firing order of 1,3,4,2. As is, you are firing the injectors in this order: 1,3,2,4. The engine will run, but...
I think on my series 1, the fuel teeth should be 2 teeth off the ignition teeth (360crank degrees off).
#3
Elite Member
Thread Starter
iTrader: (12)
Join Date: Jan 2007
Location: Hermosa Beach, CA
Posts: 2,573
Total Cats: 12
The fuel inj phase was copied over from the series 1 base map for the 94-95 miata, I noticed it didn't follow firing order so maybe the settings don't translate to the newer ecu. So should both Inj and coil phase read the same then (1=1,2=4,3=2,4=3)?. Also what the heck sets injection timing?
I am used to motec/megasquirt/performance electronics, AEM seems to handle cam/crank triggering so different so I'm having a tough time.
I am used to motec/megasquirt/performance electronics, AEM seems to handle cam/crank triggering so different so I'm having a tough time.
i'm only qualified to say anything when I'm working on my car and it's fresh in my head and I have my notebook open, otherwise I forget things fast, so that said...
I assume "coil xB" is the wasted spark version of "coil x"? If so, you only have tooth 0 & 1 accounted for. You need to have 2 & 3 in there, otherwise nothing will happen ignition wise on those 2 teeth. As you have it, both coils fire on teeth 0 & 1 at the same time, and 0 & 1 only, ut oh.
Your fuel teeth don't follow the ignition firing order of 1,3,4,2. As is, you are firing the injectors in this order: 1,3,2,4. The engine will run, but...
I think on my series 1, the fuel teeth should be 2 teeth off the ignition teeth (360crank degrees off).
I assume "coil xB" is the wasted spark version of "coil x"? If so, you only have tooth 0 & 1 accounted for. You need to have 2 & 3 in there, otherwise nothing will happen ignition wise on those 2 teeth. As you have it, both coils fire on teeth 0 & 1 at the same time, and 0 & 1 only, ut oh.
Your fuel teeth don't follow the ignition firing order of 1,3,4,2. As is, you are firing the injectors in this order: 1,3,2,4. The engine will run, but...
I think on my series 1, the fuel teeth should be 2 teeth off the ignition teeth (360crank degrees off).
#5
Elite Member
Thread Starter
iTrader: (12)
Join Date: Jan 2007
Location: Hermosa Beach, CA
Posts: 2,573
Total Cats: 12
Got an awesome answer from AEM directly, so I should be good to go. Once I get the engine running in a week or two I'll make a nice base map and post it up here so others don't have to go through the whole process again
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM