Cspence's 1992 Mazda Miata - $6700 Tuckin99 N2 / 6UL / CF HT
07-22-2010, 08:15 PM
#1
Elite Member
Thread Starter
iTrader: (11)
Join Date: Jun 2007
Location: Meriden, CT
Posts: 2,065
Total Cats: 1
Cspence's 1992 Mazda Miata - $6700 Tuckin99 N2 / 6UL / CF HT
Category: Import
Status: Clean Title
I have a 1992 Mazda Miata for sale, in USA - Connecticut.
Asking price is $7500 OBO
Well, I think the time may be coming where I need to part ways with the Miata. As of now this is more of a feeler than anything since I really don’t need to sell it, it’d just be nice to free up a little doe for the upcoming months (Wedding, Honeymoon, graduate school, house….) I purchased this car back in Feb 09 from a kid located in SC. Since then the car has run pretty much flawlessly and has brought many smiles to my face. Here is the all the info I have about the car from what either I or the PO have done. A compiled list is further down incase you don’t feel like reading, lol. Here is my build thread also… https://www.miataturbo.net/showthrea...ht=cspence%27s)
Previous owner had stated that the car weighed 2050lbs w/o gas or driver (It had a steel hood which I replaced with a stock aluminum one, but I also added the hardtop so this should still be fairly accurate)
The engine was rebuilt about ~8k miles (The original owner said the rebuild had 3K on it back in July 08. I assume he put another 1-2K on it before I bought it in Feb 09. Since then I have only put another 3-4K on the car since its strictly a weekend/fun car) . It has a flyin Miata high boost head gasket and arp head studs but it still has stock rods/pistons. It has a brand new oil pump, water pump, main/rod bearings, seals, gaskets rings hoses and everything.
The car has a mild steel log manifold with a gt28 off of a nissan pulsar gtir. The turbo should support 270 whp. i currently have it set at 18 psi but still have yet to dyno it. Based on how it performs next to other local Turbo Miatas, I would guess its in the 230-240 whp bracket right now. Its got a full 3 inch exhaust with an external Tial 38mm waste gate dumping into the Stainless downpipe. It has 2.5 inch stainless intercooler piping and a large bar and plate intercooler up front. It goes into a sheetmetal intake manifold that has no idle control valve or anything on it (idles and starts up great anyways ) fuel management is a megasquirt v 2.2. I’m using RC 440's (I have a set of Low Impedance RC 550’s w/ resistor packs that I could include with the car for an additional $150) and a Walbro 190. The bov is a greddy rs knock off. The car has passed CT emissions without a hitch (Sniffer test)
GT28 off a Nissan Pulsar
Custom Mild Steel Log manifold
38mm Tial EW
3” Stainless downpipe
3” TBE with resonator and magnaflow straight through bullet muffler
2.5” Stainless intercooler piping, with high quality silicon couplers and T-Bolt clamps
24”x6”x3” Custom Bar & Plate Intercooler (Custom end tanks)
24”x19”x3” Custom Aluminum Radiator
Custom sheet metal intake manifold
RC440 Injectors (I also have a set of Low impedance RC 550’s w/ resistor packs which I could include for $150 if you plan to make more power and need to increase the fueling)
Walbro 190
Flyin Miata ACT clutch, street disk and exteme pressure plate
Flyin Miata High Boost head gasket
ARP Studs
Megasquirt v2.2 (I also have a full purchased version of Tunerstudio which I could include for free if wanted)
Polski Detcans for tuning can be included if desired. Made by our own Jeff_Ciesielski
Stock valve Koni yellows with 6000k miles on them
H&R race springs with the rates of 500 front and 325 rear
Custom top hats (i have 4 inches of travel at the current ride height)
1" flyin miata front sway bar and stock rear
949Racing Subframe braces (Which have been discontinued, but work great!)
Bolt on Frame Rails
M Edition rear brace
Rear tow hook
Adjustable endlinks all around
Poly Bushings all around
Mazdaspeed motor mounts
Fat cat bump stops
All good ball joints/ wheel bearings
1.8 brakes all around with ebc red's
Stainless steel brake lines all around
Custom Master cylinder stopper (For a firmer, more responsive pedal)
front brakes have vents coming from the lip to the center of the disk
Delrin differential bushings
1.8L rear end conversion with a custom made clutch pack lsd from a rx7 guru in Asheville
1.8L Tranny (Second gear occasionally grinds when shifting hard from 1st to 2nd, but is fine if shifting easy)
New master & slave brake cylinders replaced in Oct 09.
15x9 Black 6UL’s wrapped in 225/45R15 Toyo R1r’s both purchased in Mar 10 (<1000mi on wheels/tires)
30mm Rear 19mm Front Adapter style wheel spacers (Motorsport Tech, http://www.motorsport-tech.com/)
REAL Tuckin99 N2 flares
Carbing 3pt STB w/ custom Master cylinder stopper (Made by me ;) )
RX330 HID Projectors in the turn signal openings
Polished hood with molded headlight lids, NACA headlight duct, and Z34 vent over turbo
Sheet Metal bumper scoop (Made by me)
Sheet metal intake scoop under NACA duct.
Gutted Doors with drop in windows
3M Di-noc carbon wrap
Smoked tail lights (Braineack special)
AEM Uego WB
AEM Tru Boost EBC
Custom Double Din sheet metal gauge panel made by me.
Pioneer CD player w/ custom hidden mount behind glove box door
MB Quart 6.5" door speakers wired with stinger wire
ChaserAero Carbon Fiber HT w/ Rennenmetal Brackets Purchased in Feb 10.
Tranny, Shifter Turret, differential oils were all changed back on 6-7-09 using Full synthetic Amsoil products (Purchased from SoflaRick) 75w90 Amsoil Severe Gear for the Rear end, GL5 75w90 & Sliplock for the Tranny.
Shell Rotella Syn and Wix filters are my oil / filter of choice as is with many others
Car passed CT emissions (Sniffer only) without a hitch back in Mar 09.
Now, for a few things the car does not have...
heat
ac
soft top
passenger mirror
flip up headlights
wipers
This car has probably been the most fun car I have ever owned and probably ever driven. Its not the fastest thing on the road (Although it can usually hold its own, lol) but it handles like a *****!! If your at all interested in this car, you should know that it is by no means a beauty queen and would probably NOT make a good DD. It would however make a great weekend warrior (as it was for me) or track car. If someone would like to purchase the car without the Wheels (-$900 – would need to supply own wheels), the hardtop (-$1000), or the STB ($-200) it can be done. I probably have $13K into the car and am looking for $7500 (with everything). I am open to shipping the car, but the buyer must make all arrangements and cover the fees. Like I mentioned earlier, I did originally ship this car from SC, so I have had some experience in that respect and would have no problems working that out with you. As many people on MT.net can attest, I am an honest and straight up guy, so please have no worries about this transaction. If anyone has any questions please let me know via post, pm, or email – SpenceChristopher@yahoo.com.
4-27.jpg?t=1269196920
IMG_8592.jpg?t=1273977027
IMG_8554.jpg?t=1273977072
IMG_8555.jpg?t=1273977104
7-23.jpg?t=1273188021
IMG_8171.jpg?t=1273887694
CIMG2184.jpg?t=1205006042
CIMG2174.jpg?t=1205006170
2-18.jpg?t=1265416401
1-21.jpg?t=1266704831
2-20.jpg?t=1266704901
3-19.jpg?t=1266704933
1-25.jpg?t=1268179917
2-24.jpg?t=1268179972
1-22.jpg?t=1267486353
3-15.jpg?t=1264027039
You can tell these are real Tuckin99 N2 flares since the gel coat is white and the fender is specified under the resin on the under side of the flares.
1-27.jpg?t=1268369130
Status: Clean Title
I have a 1992 Mazda Miata for sale, in USA - Connecticut.
Asking price is $7500 OBO
Well, I think the time may be coming where I need to part ways with the Miata. As of now this is more of a feeler than anything since I really don’t need to sell it, it’d just be nice to free up a little doe for the upcoming months (Wedding, Honeymoon, graduate school, house….) I purchased this car back in Feb 09 from a kid located in SC. Since then the car has run pretty much flawlessly and has brought many smiles to my face. Here is the all the info I have about the car from what either I or the PO have done. A compiled list is further down incase you don’t feel like reading, lol. Here is my build thread also… https://www.miataturbo.net/showthrea...ht=cspence%27s)
Previous owner had stated that the car weighed 2050lbs w/o gas or driver (It had a steel hood which I replaced with a stock aluminum one, but I also added the hardtop so this should still be fairly accurate)
The engine was rebuilt about ~8k miles (The original owner said the rebuild had 3K on it back in July 08. I assume he put another 1-2K on it before I bought it in Feb 09. Since then I have only put another 3-4K on the car since its strictly a weekend/fun car) . It has a flyin Miata high boost head gasket and arp head studs but it still has stock rods/pistons. It has a brand new oil pump, water pump, main/rod bearings, seals, gaskets rings hoses and everything.
The car has a mild steel log manifold with a gt28 off of a nissan pulsar gtir. The turbo should support 270 whp. i currently have it set at 18 psi but still have yet to dyno it. Based on how it performs next to other local Turbo Miatas, I would guess its in the 230-240 whp bracket right now. Its got a full 3 inch exhaust with an external Tial 38mm waste gate dumping into the Stainless downpipe. It has 2.5 inch stainless intercooler piping and a large bar and plate intercooler up front. It goes into a sheetmetal intake manifold that has no idle control valve or anything on it (idles and starts up great anyways ) fuel management is a megasquirt v 2.2. I’m using RC 440's (I have a set of Low Impedance RC 550’s w/ resistor packs that I could include with the car for an additional $150) and a Walbro 190. The bov is a greddy rs knock off. The car has passed CT emissions without a hitch (Sniffer test)
GT28 off a Nissan Pulsar
Custom Mild Steel Log manifold
38mm Tial EW
3” Stainless downpipe
3” TBE with resonator and magnaflow straight through bullet muffler
2.5” Stainless intercooler piping, with high quality silicon couplers and T-Bolt clamps
24”x6”x3” Custom Bar & Plate Intercooler (Custom end tanks)
24”x19”x3” Custom Aluminum Radiator
Custom sheet metal intake manifold
RC440 Injectors (I also have a set of Low impedance RC 550’s w/ resistor packs which I could include for $150 if you plan to make more power and need to increase the fueling)
Walbro 190
Flyin Miata ACT clutch, street disk and exteme pressure plate
Flyin Miata High Boost head gasket
ARP Studs
Megasquirt v2.2 (I also have a full purchased version of Tunerstudio which I could include for free if wanted)
Polski Detcans for tuning can be included if desired. Made by our own Jeff_Ciesielski
Stock valve Koni yellows with 6000k miles on them
H&R race springs with the rates of 500 front and 325 rear
Custom top hats (i have 4 inches of travel at the current ride height)
1" flyin miata front sway bar and stock rear
949Racing Subframe braces (Which have been discontinued, but work great!)
Bolt on Frame Rails
M Edition rear brace
Rear tow hook
Adjustable endlinks all around
Poly Bushings all around
Mazdaspeed motor mounts
Fat cat bump stops
All good ball joints/ wheel bearings
1.8 brakes all around with ebc red's
Stainless steel brake lines all around
Custom Master cylinder stopper (For a firmer, more responsive pedal)
front brakes have vents coming from the lip to the center of the disk
Delrin differential bushings
1.8L rear end conversion with a custom made clutch pack lsd from a rx7 guru in Asheville
1.8L Tranny (Second gear occasionally grinds when shifting hard from 1st to 2nd, but is fine if shifting easy)
New master & slave brake cylinders replaced in Oct 09.
15x9 Black 6UL’s wrapped in 225/45R15 Toyo R1r’s both purchased in Mar 10 (<1000mi on wheels/tires)
30mm Rear 19mm Front Adapter style wheel spacers (Motorsport Tech, http://www.motorsport-tech.com/)
REAL Tuckin99 N2 flares
Carbing 3pt STB w/ custom Master cylinder stopper (Made by me ;) )
RX330 HID Projectors in the turn signal openings
Polished hood with molded headlight lids, NACA headlight duct, and Z34 vent over turbo
Sheet Metal bumper scoop (Made by me)
Sheet metal intake scoop under NACA duct.
Gutted Doors with drop in windows
3M Di-noc carbon wrap
Smoked tail lights (Braineack special)
AEM Uego WB
AEM Tru Boost EBC
Custom Double Din sheet metal gauge panel made by me.
Pioneer CD player w/ custom hidden mount behind glove box door
MB Quart 6.5" door speakers wired with stinger wire
ChaserAero Carbon Fiber HT w/ Rennenmetal Brackets Purchased in Feb 10.
Tranny, Shifter Turret, differential oils were all changed back on 6-7-09 using Full synthetic Amsoil products (Purchased from SoflaRick) 75w90 Amsoil Severe Gear for the Rear end, GL5 75w90 & Sliplock for the Tranny.
Shell Rotella Syn and Wix filters are my oil / filter of choice as is with many others
Car passed CT emissions (Sniffer only) without a hitch back in Mar 09.
Now, for a few things the car does not have...
heat
ac
soft top
passenger mirror
flip up headlights
wipers
This car has probably been the most fun car I have ever owned and probably ever driven. Its not the fastest thing on the road (Although it can usually hold its own, lol) but it handles like a *****!! If your at all interested in this car, you should know that it is by no means a beauty queen and would probably NOT make a good DD. It would however make a great weekend warrior (as it was for me) or track car. If someone would like to purchase the car without the Wheels (-$900 – would need to supply own wheels), the hardtop (-$1000), or the STB ($-200) it can be done. I probably have $13K into the car and am looking for $7500 (with everything). I am open to shipping the car, but the buyer must make all arrangements and cover the fees. Like I mentioned earlier, I did originally ship this car from SC, so I have had some experience in that respect and would have no problems working that out with you. As many people on MT.net can attest, I am an honest and straight up guy, so please have no worries about this transaction. If anyone has any questions please let me know via post, pm, or email – SpenceChristopher@yahoo.com.
4-27.jpg?t=1269196920
IMG_8592.jpg?t=1273977027
IMG_8554.jpg?t=1273977072
IMG_8555.jpg?t=1273977104
7-23.jpg?t=1273188021
IMG_8171.jpg?t=1273887694
CIMG2184.jpg?t=1205006042
CIMG2174.jpg?t=1205006170
2-18.jpg?t=1265416401
1-21.jpg?t=1266704831
2-20.jpg?t=1266704901
3-19.jpg?t=1266704933
1-25.jpg?t=1268179917
2-24.jpg?t=1268179972
1-22.jpg?t=1267486353
3-15.jpg?t=1264027039
You can tell these are real Tuckin99 N2 flares since the gel coat is white and the fender is specified under the resin on the under side of the flares.
1-27.jpg?t=1268369130
Last edited by Cspence; 08-14-2010 at 06:06 PM.
Reply
0
0
07-22-2010, 09:51 PM
#5
Elite Member
Thread Starter
iTrader: (11)
Join Date: Jun 2007
Location: Meriden, CT
Posts: 2,065
Total Cats: 1
No parting out yet guys 
. If she doesn't sell whole or close to whole I'll probably hang on to it and continue to enjoy it. I'm not even going as far as to post anything on craiglist yet, even though the market here is pretty slim since most everyone here already has a miata (Although you never know if someone has a buddy that may be interested and/or if there are any lurkers/noobs out there 
)
I'll tell ya though, this is very hard to do....its my first time selling a modded car and its tough to see how money flew out the window putting this thing together and now adding it all up knowing I'll get nowhere near what I got into it
. If she doesn't sell whole or close to whole I'll probably hang on to it and continue to enjoy it. I'm not even going as far as to post anything on craiglist yet, even though the market here is pretty slim since most everyone here already has a miata (Although you never know if someone has a buddy that may be interested and/or if there are any lurkers/noobs out there )I'll tell ya though, this is very hard to do....its my first time selling a modded car and its tough to see how money flew out the window putting this thing together and now adding it all up knowing I'll get nowhere near what I got into it
Reply
0
0
07-26-2010, 04:53 PM
#19
Elite Member
Thread Starter
iTrader: (11)
Join Date: Jun 2007
Location: Meriden, CT
Posts: 2,065
Total Cats: 1
Remember guys, you can opt out from some bits and pieces if you want to drop the price some....Also, I will entertain offers, just no lowballers please.
Reply
0
0
07-26-2010, 05:24 PM
#20
No way! I didnt even get to see the ******* thing in person yet!! lol
I've had the thought of selling or parting out mine about 100 times over the past year, but so far it hasn't come to that.
Hopefully you can keep it, but if it has to go I hope you get the price you want, god knows its worth it.
I've had the thought of selling or parting out mine about 100 times over the past year, but so far it hasn't come to that.
Hopefully you can keep it, but if it has to go I hope you get the price you want, god knows its worth it.
Reply
0
0
