DIY Turbo Discussion greddy on a 1.8? homebrew kit?

How do you know if drain line is working?

Thread Tools
 
Search this Thread
 
Old 01-01-2012, 11:48 AM
  #1  
Junior Member
Thread Starter
 
dliverance's Avatar
 
Join Date: Jun 2010
Location: Hollywood Fl
Posts: 61
Total Cats: 2
Default How do you know if drain line is working?

I did some searching but I couldn't find anything on this topic. I recently installed my turbo and I had to custom make my oil lines. For the drain line I have a 20" line with -8an fittings. The turbo is a TD05 and coming off the turbo i have a 1/2" NPT to -8an fitting. In the oil pan I have a 3/8" NPT to -8an.

The turbo is oil and water cooled. It doesn't make noise but then again I have only had it on the car for a few days.

My concern is that the -8an fittings are too restrictive but according to the links below, 3/8" NPT is fine.

http://revlimiter.net/blog/2010/07/drilling-for-oil/

http://www.bellengineering.net/templ...ons_BEGi-S.pdf

When I was looking at the fittings before the install, the 3/8" NPT looked to be the same size opening as the -8an so I figured it would be safe but I just want to hear your opinions.

BTW the car is a 99 making 8psi but I intend to bump it up to 10psi eventually.
dliverance is offline  
Old 01-01-2012, 11:55 AM
  #2  
Senior Member
iTrader: (14)
 
94mx5red's Avatar
 
Join Date: Oct 2006
Location: South East Florida
Posts: 677
Total Cats: 6
Default

Disconnect the line from the pan and aim at a container. Start the car, and watch your flow.
94mx5red is offline  
Old 01-01-2012, 01:05 PM
  #3  
Junior Member
Thread Starter
 
dliverance's Avatar
 
Join Date: Jun 2010
Location: Hollywood Fl
Posts: 61
Total Cats: 2
Default

I'm not sure what I would be comparing the flow to
dliverance is offline  
Old 01-01-2012, 01:12 PM
  #4  
I'm a terrible person
iTrader: (19)
 
FRT_Fun's Avatar
 
Join Date: Apr 2009
Location: Arizona
Posts: 7,174
Total Cats: 180
Default

So you are not worried that it *isn't flowing* you are worried if it is flowing enough? Honestly with the pieces you describe above there should be no flow issues. -8an is 1/2" OD, so I'm guessing probably 3/8 ID or close.
FRT_Fun is offline  
Old 01-01-2012, 01:49 PM
  #5  
Elite Member
 
dustinb's Avatar
 
Join Date: Feb 2008
Location: Victoria, BC
Posts: 2,320
Total Cats: 13
Default

If you're not blowing mass amounts of smoke right now then you are flowing fine.
dustinb is offline  
Old 01-01-2012, 01:54 PM
  #6  
Antisaint
iTrader: (17)
 
Vashthestampede's Avatar
 
Join Date: Feb 2007
Location: Danbury, CT
Posts: 4,564
Total Cats: 58
Default

Whenever I checked my drain line I would just pop it off the oil pan fitting and stick it in to a coffee can, then start the car and shut it off. I usually would check the feed line while I was at it, and usually before I'd check the drain.
Vashthestampede is offline  
Old 01-01-2012, 02:08 PM
  #7  
Junior Member
Thread Starter
 
dliverance's Avatar
 
Join Date: Jun 2010
Location: Hollywood Fl
Posts: 61
Total Cats: 2
Default

Originally Posted by FRT_Fun
So you are not worried that it *isn't flowing* you are worried if it is flowing enough? Honestly with the pieces you describe above there should be no flow issues. -8an is 1/2" OD, so I'm guessing probably 3/8 ID or close.
Originally Posted by dustinb
If you're not blowing mass amounts of smoke right now then you are flowing fine.
Thanks guys. This is exactly what I needed to know. I know most people use a -10an but I just wanted to make sure I wasn't risking anything by using a -8.
dliverance is offline  
Old 01-06-2012, 10:08 AM
  #8  
Elite Member
iTrader: (2)
 
Faeflora's Avatar
 
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Default

If your turbo doesn't die and start screaming (literally) on your first full range rpm pull you are probably ok. no smoke is a sign of happy turbo too
Faeflora is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM



Quick Reply: How do you know if drain line is working?



All times are GMT -4. The time now is 08:33 AM.