COP Thread
06-11-2011, 09:23 PM
#1422
Junior Member
Join Date: Aug 2009
Location: Sun Prairie WI
Posts: 50
Total Cats: 1
Well just the connectors are $9 each my cost from Toyota. Th harness is of a used engine I installed that had 20k on it. So I'd sell the whole harness for that price which would be 50.95 with shipping.
Reply
0
0
06-13-2011, 01:17 PM
#1425
I'm Miserable!
Join Date: May 2011
Posts: 38
Total Cats: 0
if you are pulling and cutting the connectors off of a harness then they wont have a part number. There are places online you can buy just the connectors though. I learned that on this forum actually. search around youll find it.
if you are asking what part number my coils are.... 90080 19015
if you are asking what part number my coils are.... 90080 19015
Reply
0
0
06-14-2011, 06:19 PM
#1427
Again, I already have the connectors that plug into the coils. My plugs have 3 wires coming out of them, not the 4 required for a 94-95. Is there any way to buy the little pieces that go into the connector to add the additional wire? Maybe it's called the "terminal" from the saved COP post?
I'd put a picture up but there's stored away somewhere and I haven't really began looking for them since I moved recently.
Edit: Found a pic. I just need the little white terminals for each plug (4 total).
I'd put a picture up but there's stored away somewhere and I haven't really began looking for them since I moved recently.
Edit: Found a pic. I just need the little white terminals for each plug (4 total).
Reply
0
0
06-22-2011, 01:57 PM
#1430
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,441
Total Cats: 1,899
COPs are in and she runs great! Connectors with pigtails I purchased from Ballenger Motorsports as listed previously in this thread and in the FAQ. As you can see, the BM connectors are white and ALL the wires in the pigtails are black. It can get confusing during assembly, but that's why I have a Fluke DMM with continuity tester. I could not find coils locally so I bought from Splitime in the FS section. I can post the Toyota PN later if anyone is interested. Capacitor is a 10,000uf 25v model from Frys Electronics. I threw some 1" loom around it and there was still about 1/4" of gap at the split. I have a far smaller 16v but I couldn't find it at the time. I'm not running the dwell reducer circuit at this point because I don't feel I have the skills to build one. Anyone want to sell me one?
The car is a CA Emissions spec NB1 with factory ECU (for now) so sucks on whoever said these things will not run with a CA spec ECU. Valve cover is unmodified. The COPS were a little tight to get in, but a whack with the top of my hand seated them just fine. They actually feel secure enough that I don't feel a need to build a hold down plate quite yet. I built the harness with a 6 position weatherpack connector that Splitime included with his kit of parts. I need to add a ring terminal for my additional block ground, but it seems to work fine without it for now.
Another 6pin weatherpack on the factory coil connectors so I can swap back if the need arises.
Big time +1 to all the folks who helped develop and explain this so n00bs like me could figure it out. It's great to have a cheap alternative to the FAILBOAT 99/00 factory coils.
Time to add COPs to my signature and open up the gaps on them plugs!
The car is a CA Emissions spec NB1 with factory ECU (for now) so sucks on whoever said these things will not run with a CA spec ECU. Valve cover is unmodified. The COPS were a little tight to get in, but a whack with the top of my hand seated them just fine. They actually feel secure enough that I don't feel a need to build a hold down plate quite yet. I built the harness with a 6 position weatherpack connector that Splitime included with his kit of parts. I need to add a ring terminal for my additional block ground, but it seems to work fine without it for now.
Another 6pin weatherpack on the factory coil connectors so I can swap back if the need arises.
Big time +1 to all the folks who helped develop and explain this so n00bs like me could figure it out. It's great to have a cheap alternative to the FAILBOAT 99/00 factory coils.
Time to add COPs to my signature and open up the gaps on them plugs!
Reply
0
0
06-22-2011, 02:22 PM
#1433
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,441
Total Cats: 1,899
They go faster that way? 
It made it easier to remove the connectors while test fitting. Hivemind seems to like the cap and it came with the bag-o-parts I got from Splitime, so why not use it?
I can point them the other way if it makes
happy 
It made it easier to remove the connectors while test fitting. Hivemind seems to like the cap and it came with the bag-o-parts I got from Splitime, so why not use it?I can point them the other way if it makes
happy
Reply
0
0
06-22-2011, 03:15 PM
#1437
Junior Member
Join Date: May 2010
Location: Darlington, UK
Posts: 280
Total Cats: 0
63V like this onehttp://cgi.ebay.co.uk/BHC-Aerovox-10...item3f03af25a7
Or 35V like this which isnt audio
http://cgi.ebay.co.uk/Radial-Electro...item562c5c76f0
Or 35V like this which isnt audio
http://cgi.ebay.co.uk/Radial-Electro...item562c5c76f0
Reply
0
0
