johndoe

iTrader: (5)

Better design or not isn't going to matter to you when your ill-fitting Begi piece makes your exhaust bang around the underbody like a ****. I'd go with something that was a guaranteed to fit if I was going to order a piece again or I'd get one made locally/learn how to weld and do it myself.

wayne_curr

iTrader: (8)

Is a Nissan T25 even capable of 200whp? I know I wasn't exactly expecting that much with mine.

boileralum

iTrader: (8)

I have heard of people getting 250whp on a SR20DET w/ the stock turbo, so I would think we could get at least 200whp with a little less displacement. I am hoping for 200-225 out of mine.

kenzo42

iTrader: (6)

SamNavy made ~200whp. I think he was also using Borla duals as the exhaust, so it could only have gone up if he changed out the exhaust.

Saml01

iTrader: (9)

Go with the Begi S.

Save your money, get something going, and by the time you need more power, you will already have everything. It will be just that much simpler to pull the trigger because you know you didnt pay a lot for something not here nor there that isnt letting you justify another upgrade.

My

Besides man, think about it. The rest of your build is cheap, why even bother with a better DP. Trust me the Begi S is plenty. Either go all the way with every part, or none of the way.

Stephanie Turner

There are many things that are superior in design. And you did say design. What you refer to above is constriction. But let's break both down...

~Cast upper section - weights more than stainless. The entire SG SP weights 12 lbs. It is highly unlikely that the FM casting plus the lower section weights less than that. Our cast upper section used to weigh 11 lbs.

This part also contains the "Separated gases" design. Are you telling me that the 3" of separation is superior to our 20"+ length? You can't. Period. In all reality, our worst downpipe - the latest BEGI-S - is still superior to the FM design.And cheaper to boot.

~Mandrel bent lower halves - something to be said for that. However, your statement of zero welds is false. I know of at least two welds, possible more, that HAVE to exist on that pipe. When FM was first designing this pipe, Bill made a point of saying that it cut the existing number of welds (which was 7 at the time) in half. But lets be honest here - cracks in welds usually occur at the flange. Their flange is welded on, so it ours. I have never seen a downpipe crack in the middle, only at the flanges. They have the same opportunity to crack as ours. Besides, we use mandrel bent tubes also. Just a few more than they do.

~O2 sensor bung in a usable place - I would have totally agreed with a year ago. But, we seem to have all the bugs worked out, or we are getting closer at least. Both with the stock sensor and WB O2.

~Fits properly - no one can guarantee fit of a pipe. There are different cross members on certain year cars. People have modified existing exhaust systems. Too much room for error. And most people are not the original owners, so who knows what has been done. I have seen some strange stuff. Sure, we get downpipes that bolt right up here, and we get some where a cross brace has to be modified. But I bet if you start asking, people with FM turbo kits had to have things welded locally etc. I know I have read as much on the m.net website posts. So this one is a toss up.

~Ease of install - No doubt, FM has us beat there. Our downpipe will be harder to install. But 99% of people say it was worth it.

~Durability - I'd have to say this is a toss up to. I have had one reported crack in a SG downpipe in 4 years. A casting can crack, it is a little less likely. But it all depends on metal alloys and the casting processes used.

My dyno charts show equally decent spool, and our pipe has also been used on several high HP applications. They only way to get a correct comparison is on the same car, different downpipes back to back. I have already volunteered to test it, and pay for the expense to do so. Bring me a car with an FM pipe. We can test it, the owner can install the new one, and if mine is worse, the owner can have the pipe for free. Plus they just got free dyno runs.

Warranties, I am sure are the same. Our pipe does cost $66 more than the FM pieces. So in the end, the owner will have to decide if it is worth it for them. But I do stand behind my statement that the design is superior, and installation of the FM piece is "totally" easier to install. If than for nothing else, the vent tube is about 5 times longer than the FM piece.
Stephanie

Saml01

iTrader: (9)

^ Steph, can I just be really honest and say youre totally hot when youre angry.

Mikeymx5

iTrader: (2)

The begi down pipe can be a pain in the you know what to install... At least from my experience.... It was the only part of my kit that I didnt care for.

If corky gets rid of that anchor bolt and prewelds the gosh dam thing, it might not be so bad and possibly even PnP. I would pay for the extra shipping if thats what it takes, its cheaper than finding a welder. However with that being said I would still choose a BEGI kit over FM if i had to do it again.

As far as numbers I really wish someone would dyno them both on the same car and tune and put down some numbers, I really dont think that 200-220 at the wheels is going to make much of a difference on any of the three. So keep the one that is stainless

wayne_curr

iTrader: (8)

I'm with you on all of this. My dp was pretty difficult to install, but works after following the instructions closely. I have not yet, however, been able to get rid of a nasty, stupid sounding exhaust leak at the slip joint.

ZX-Tex

iTrader: (15)

For the slip-joint leak, assuming the bolt is tight, try some high-temp silicone.

FWIW my stainless BEGI-S pipe fit perfectly on the first try, and the stock and WBO2 bungs were correctly located. I just picked up my BEGI SGDP (stainless) today and it is beautiful, just like the S4 manifold. I'll be installing both this weekend.

Edit: Got the stuff installed today. The DP fit just fine.

jayc72

iTrader: (14)

My bad, 4 welds, not zero. I wasn't thinking of the welds on the flanges and o2 bungs.

Mach929

iTrader: (3)

+1 i've yet to see any evidence of superiority of a separated gas downpipe

TurboTim

iTrader: (9)

What if someone made a 3" bellmouthed downpipe? (3" starting at the turbo)

paul

iTrader: (21)

If they used that 3" bellmouthed downpipe with a measly 2554 I bet they could make 233hp/235ft-lbs with a decent tune one a very old *** 1.8 approaching 300k miles.

evank

iTrader: (2)

https://www.miataturbo.net/forum/t33260/

This guy's car made 210 hp / 198 ft. lbs. while my very similar car made 213 hp and 205 ft. lb. .... so big deal you say, I gained 3 top-end hp and 7 ft. lbs. ... but consider than other guy had a boost controller and a big IC, whereas my car ran wastegate pressure and a puny IC ... yet my car still made more power. I attribute that to the SGDP (thank you TurboTim / Shore Motorsports).

The next time I get to a dyno, I might take one pull at 11 psi (vs. 15 that I run now) just for comparison sake now that my car has MS / boost controller / big IC.

Mikeymx5

iTrader: (2)

What boost was he running, Im making around 210-213 ant 11psi.... If you are doing 213 at 15 psi that doesn't seem very good.

Well I guess if you are still running the stock MSM turbo maybe?

I think that you would have to consider cars with the same turbo setup, size and boost pressure. 5-8 hp difference I probably would not even pay attention to because of the differences in motor tolerences tunes ect.

Stephanie Turner

While it would be easier to install, but the design is lacking. It will create too much turbulence, therefore impeding the flow of gases. There is also the problem of too large of an opening off of the turbo. There is no reason for a 2" hole to have a 3" opening.
Stephanie

Stephanie Turner

I was not counting O2 bungs. There are welds at the flanges though. Last time we looked into it - it was not possible to make that many tight radius bends on one bending machine, on one tube.
Stephanie

Stephanie Turner

I would use a rubber mallet and make the opening smaller. Just be gentle. The metal should expand and seal itself.
Stephanie

TurboTim

iTrader: (9)

Evan is using the stock MSM turbo.