Help with my diypnp - Miata Turbo Forum -Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


DIY Turbo Discussion greddy on a 1.8? homebrew kit?

Reply
 
 
 
LinkBack Thread Tools
Old 10-07-2016, 02:57 AM   #1
Newb
Thread Starter
 
Join Date: Sep 2016
Posts: 15
Total Cats: -8
Default Help with my diypnp

So I just got done assembling my diy, I installed the firmware and it works on my pc what I'm wondering is if I did the wiring correct (the adapter board) and the jumper cables. Please help and if it is correct can I just plug it in and load there map





jvaz8367 is offline   Reply With Quote
Old 10-07-2016, 08:00 AM   #2
Boost Czar

iTrader: (60)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 70,411
Total Cats: 1,426
Default

youre missing the idle fly-back diode and vr and opto pull-up resistors. Bottom right of second shot under NITROUS INPUT


at a quick glance it looks good, I'd personally remove FP from the HIGH SIDE DRIVER and connect it straight to 4O. Then using spare wire, make a small bridge between the 2O pin on the AFM connector and the FP Relay pin.


you need to remove the variable resistor on R19.
Braineack is online now   Reply With Quote
Old 10-07-2016, 10:09 AM   #3
Newb
Thread Starter
 
Join Date: Sep 2016
Posts: 15
Total Cats: -8
Default

This is the board without the micro squirt

These are the resistors and diodes I had said

So I will remove the r19 resistor right I was also told to remove the r39 as well where can I find the idle fly back diode spot I have one diode left and it said extra where do I add it to exactly I also have the 3 470ohm resistors for pull ups is that the ones I have to solder onto the vr and opto sports you pointed out
jvaz8367 is offline   Reply With Quote
Old 10-07-2016, 10:22 AM   #4
Newb
Thread Starter
 
Join Date: Sep 2016
Posts: 15
Total Cats: -8
Default

God this phot from online is this correct on the resistor and diode

jvaz8367 is offline   Reply With Quote
Old 10-07-2016, 11:17 AM   #5
Boost Czar

iTrader: (60)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 70,411
Total Cats: 1,426
Default

im sorry i meant r39, not r19


yes, that's how youll set them up. are you not looking at the how-to documentation on diy's website?
Braineack is online now   Reply With Quote
Old 10-07-2016, 01:02 PM   #6
Newb
Thread Starter
 
Join Date: Sep 2016
Posts: 15
Total Cats: -8
Default

Yes. I looked over them that's how I got the connections o was just asking for Someone to double check my connections
jvaz8367 is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
DIY Honda B18 intake manifold-on-miata kit 4gordeev Miata parts for sale/trade 23 01-16-2017 05:20 AM
Hydra 2.7 NB ignition settings or base map needed! curly Hydra 6 10-08-2016 12:58 PM
Map sensor and high idle Jmanwork MEGAsquirt 5 10-06-2016 03:57 AM
Adapting MS DIYBOB for '99 Harness Djwade MEGAsquirt 1 09-25-2016 04:30 PM
DIY Megasquirt 1 with v3.0 board kit w/ boostcontroller MSV30 chip schema Miata parts for sale/trade 0 09-14-2016 10:35 AM


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -4. The time now is 12:07 PM.