What knock sounds like (video)
#1
Senior Member
Thread Starter
iTrader: (7)
Join Date: Aug 2007
Location: Southern Indiana
Posts: 1,369
Total Cats: -1
What knock sounds like (video)
So, I've read a lot of threads where someone says "as long as you know what knock sounds like." I read that and think to my self well ****, i have no idea what it sounds like, so naturally, i go to youtube and see if i can find it. I wanted to post this up so people would know what knock was like. Maybe i can save some a motor.
Now, like i said, i have never personally heard knock so i am assuming that this is knock. Please, someone, correct me if I'm wrong. I'm going on the fact that someone said it sounds like shaking pennies in a can.
Now, like i said, i have never personally heard knock so i am assuming that this is knock. Please, someone, correct me if I'm wrong. I'm going on the fact that someone said it sounds like shaking pennies in a can.
#2
Elite Member
iTrader: (12)
Join Date: Jan 2007
Location: Hermosa Beach, CA
Posts: 2,573
Total Cats: 12
faint knock is very hard to hear, I can only see it on my op gauge. louder knock is very easy to hear, tust me you know it when you hear it, its like a animal is in your engine and freaking out banging everyhting trying to get out haha.
#9
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
he doesn't even get on the throttle, so unless he is the worst tuner in the world, he shouldn't have knock. but then again, he did post a video of said knock and labeled it "engine pinking". You know, when you're engine paints itself a shade of red.
#11
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
the 90-94 oil pressure sensors are carbon resistance sensors. As the carbon is compressed, the resistance changes. Detonation shock waves travel through the carbon sensors with massive changes in resistance that is indicated by the gauge needle flickering wildly to the left.
#13
the 90-94 oil pressure sensors are carbon resistance sensors. As the carbon is compressed, the resistance changes. Detonation shock waves travel through the carbon sensors with massive changes in resistance that is indicated by the gauge needle flickering wildly to the left.
Was this intended in its design or just an accidental by product?
#15
I would never boost a car without det cans. They cost 15 dollars and 15 minutes.
Your brain is a better knock filter than any computer. Det cans amplify the actual vibrations of the block, it's not a digital or analogue reproduction. You will hear the knock, and any knock you don't hear will only be seen with a 10x magnifying glass in sunlight on new plugs.
I always have my det cans with me and just plug em in if I need to take a listen.
edit: I read that link and wonder why he folded the copper over itself like that, I've never done that. Seems like it would just insert some new harmonics into the system you might want to keep out? I also compared it to the almost never recommended air compressor hose to vacuum tubing. The stiffer hose transmitted the noise a little bit more loudly, it's not worth the cost at all.
6-10 feet of 3/4" vacuum tubing
1 3/4" plastic T (brass made no difference)
1 pair plastic over-ear hearing protectors
1 3/4" copper tube
Just slide the vacuum tubing into the copper and use a bead of silicone or rtv or whatever heat resistant sealant you have around.
Your brain is a better knock filter than any computer. Det cans amplify the actual vibrations of the block, it's not a digital or analogue reproduction. You will hear the knock, and any knock you don't hear will only be seen with a 10x magnifying glass in sunlight on new plugs.
I always have my det cans with me and just plug em in if I need to take a listen.
edit: I read that link and wonder why he folded the copper over itself like that, I've never done that. Seems like it would just insert some new harmonics into the system you might want to keep out? I also compared it to the almost never recommended air compressor hose to vacuum tubing. The stiffer hose transmitted the noise a little bit more loudly, it's not worth the cost at all.
6-10 feet of 3/4" vacuum tubing
1 3/4" plastic T (brass made no difference)
1 pair plastic over-ear hearing protectors
1 3/4" copper tube
Just slide the vacuum tubing into the copper and use a bead of silicone or rtv or whatever heat resistant sealant you have around.
Last edited by opek; 04-06-2008 at 10:41 PM.
#18
Senior Member
Thread Starter
iTrader: (7)
Join Date: Aug 2007
Location: Southern Indiana
Posts: 1,369
Total Cats: -1
http://www.streetrodstuff.com/Articl...ne/Detonation/
Well, if I cant post up a good video of it, I might as well link to a great article. So here it is.
Well, if I cant post up a good video of it, I might as well link to a great article. So here it is.
#19
Elite Member
iTrader: (15)
Join Date: Sep 2007
Location: Incline Village, NV
Posts: 2,034
Total Cats: 5
the 90-94 oil pressure sensors are carbon resistance sensors. As the carbon is compressed, the resistance changes. Detonation shock waves travel through the carbon sensors with massive changes in resistance that is indicated by the gauge needle flickering wildly to the left.
Thread
Thread Starter
Forum
Replies
Last Post
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM