My turbo specs - opinions?
#1
My turbo specs - opinions?
I bought the car w/ the turbo and hack-job setup installed, none of it running. Well, now we're idling and trying to make plans to finish the project.
I wrote down the spes on the turbo today to see what you all thought of it.
T3/T4
TO4E
A/R .63
Sitting on an OBX stainless manifold. (I've heard these are junk)
There is currently a v-band clamp on the exhaust side and it's 2 1/2" mandrel bent DP to a full 2 1/2" exhaust, no cat.
Intercooler piping is 2".
Should I expect lag?
At what RPM will I make 10psi if I'm correct in thinking I have the 4.10 (open) diff. My car is the base model, not sure if that matters or not w/ the transmission gearing.
Thanks fellas.
I wrote down the spes on the turbo today to see what you all thought of it.
T3/T4
TO4E
A/R .63
Sitting on an OBX stainless manifold. (I've heard these are junk)
There is currently a v-band clamp on the exhaust side and it's 2 1/2" mandrel bent DP to a full 2 1/2" exhaust, no cat.
Intercooler piping is 2".
Should I expect lag?
At what RPM will I make 10psi if I'm correct in thinking I have the 4.10 (open) diff. My car is the base model, not sure if that matters or not w/ the transmission gearing.
Thanks fellas.
#5
I'm still trying to figure that out. I figure for now, the goal is to get the most I can out of this setup because I bought it as a whole, and I'm wanting to keep expenses down as much as possible since I'm not even sure I'll be keeping the car or buying a newer Miata to do my own start/finish on. I bought this for what I thought was a good price, and I really just want to get my feet wet w/ turbo cars and modifying in general.
So that all said, I'd like to dyno at 200whp. That would make me grin. But more than that, I'd like to hit 10psi (where I plan to run it on the street) at like 3,000 RPM or less if possible.
So that all said, I'd like to dyno at 200whp. That would make me grin. But more than that, I'd like to hit 10psi (where I plan to run it on the street) at like 3,000 RPM or less if possible.
#6
if you want 200whp and 10psi by 3K it's recommend a smaller turbo. since you're already a t3 platform i'd recommend a t3 super 60, search it's well documented on the this and run by braineack. however that turbo even on a 1.8 might fall a bit short on your desired spool on certain setups. 3" exhaust and headwork are your friends.
you could also go for a 50 trim t3 but it won't be able to make much more than 200whp when your goals climb
the turbo you have now is a good turbo for a 300whp+ application
you could also go for a 50 trim t3 but it won't be able to make much more than 200whp when your goals climb
the turbo you have now is a good turbo for a 300whp+ application
#7
if you want 200whp and 10psi by 3K it's recommend a smaller turbo. since you're already a t3 platform i'd recommend a t3 super 60, search it's well documented on the this and run by braineack. however that turbo even on a 1.8 might fall a bit short on your desired spool on certain setups. 3" exhaust and headwork are your friends.
you could also go for a 50 trim t3 but it won't be able to make much more than 200whp when your goals climb
the turbo you have now is a good turbo for a 300whp+ application
you could also go for a 50 trim t3 but it won't be able to make much more than 200whp when your goals climb
the turbo you have now is a good turbo for a 300whp+ application
300+hp with this turbo? That's impressive.
So, I'm re-doing my DP currently anyway because the bungs for the o2 and WB were installed too close to the turbo, should I just cut the entire DP off and scrap it, save the 2.5" v-band, and buy a 2.5"x3" exhaust adapter and finish the car w/ 3"? I'm only planning to run the exhaust as far as necessary to install a glasspack and two side exit tips on the passenger side, probably exiting in front of the passenger rear wheel.
When you say headwork, I'm assuming you mean port the exhaust side as much as possible, correct?
I just want to write a brief note on why I'm such a newb. lol
I've been a Camaro guy for 7 years, I slapped headers on two different LT1's and made 300+whp and was happy as could be. This is a whole new game for me. Seems to be pretty technical.
#9
Elite Member
iTrader: (22)
Join Date: Dec 2006
Location: Sunny Spanish speaking Non US Caribbean
Posts: 3,224
Total Cats: 3
John, I have a T3/T4 on a 96 also. I have a 2.5" exhaust and made 212whp at 9psi. I used to see full boost around 4,200 rpm.
I think you're going to need bigger injectors soon. If you're mechanically inclined I would consider doing something to the head. That should help you see boost earlier in the rpm band. Other options, such as a 3" exhaust would be too expensive.
I think you're going to need bigger injectors soon. If you're mechanically inclined I would consider doing something to the head. That should help you see boost earlier in the rpm band. Other options, such as a 3" exhaust would be too expensive.
#10
212 at 9psi? Did you have any head work done or were you all stock? That's a pretty good number.
I was under the impression that with the 190HP fuel pump and the EMB I could run the 305cc injectors and be pretty safe? What injectors would you recommend? I went looking for the 305's because I wanted a PNP injector rather than wiring up resistors, but I can solder, so I guess if it's widely agreed I should upgrade, I'll do it now rather than later. They aren't even installed yet.
I was under the impression that with the 190HP fuel pump and the EMB I could run the 305cc injectors and be pretty safe? What injectors would you recommend? I went looking for the 305's because I wanted a PNP injector rather than wiring up resistors, but I can solder, so I guess if it's widely agreed I should upgrade, I'll do it now rather than later. They aren't even installed yet.
#11
Guys, more background.
The car will probably just be a toy for street driving. I have the Camaro for Auto-X, but might take the Miata a time or two. So more than likely, I'll just use the car to surprise ricers, challenge friends, carve some country roads, etc.
Would any of you suggest I take an offer from someone and trade to a 25k mile used gt2560r w/ BEGi manifold and downpipe for my current setup?
Benefits vs. non-benefits?
I understand it'll be quicker spool, but does it fall flat up top? Should I even worry about that since I'll rarely see redline? What is the most boost/HP I could attain w/ a 2560r if I ever wanted to go faster (which seems to happen to all junkies)??
The car will probably just be a toy for street driving. I have the Camaro for Auto-X, but might take the Miata a time or two. So more than likely, I'll just use the car to surprise ricers, challenge friends, carve some country roads, etc.
Would any of you suggest I take an offer from someone and trade to a 25k mile used gt2560r w/ BEGi manifold and downpipe for my current setup?
Benefits vs. non-benefits?
I understand it'll be quicker spool, but does it fall flat up top? Should I even worry about that since I'll rarely see redline? What is the most boost/HP I could attain w/ a 2560r if I ever wanted to go faster (which seems to happen to all junkies)??
#12
Elite Member
iTrader: (22)
Join Date: Dec 2006
Location: Sunny Spanish speaking Non US Caribbean
Posts: 3,224
Total Cats: 3
212 at 9psi? Did you have any head work done or were you all stock? That's a pretty good number.
I was under the impression that with the 190HP fuel pump and the EMB I could run the 305cc injectors and be pretty safe? What injectors would you recommend? I went looking for the 305's because I wanted a PNP injector rather than wiring up resistors, but I can solder, so I guess if it's widely agreed I should upgrade, I'll do it now rather than later. They aren't even installed yet.
I was under the impression that with the 190HP fuel pump and the EMB I could run the 305cc injectors and be pretty safe? What injectors would you recommend? I went looking for the 305's because I wanted a PNP injector rather than wiring up resistors, but I can solder, so I guess if it's widely agreed I should upgrade, I'll do it now rather than later. They aren't even installed yet.
You can check the dyno sheet in that section. I posted it a while back.
About the injectors: my suggestion would be to look for 550cc. We all start with a specific whp goal in mind and end up braking it. Ask me how I know!
#13
Elite Member
iTrader: (22)
Join Date: Dec 2006
Location: Sunny Spanish speaking Non US Caribbean
Posts: 3,224
Total Cats: 3
Guys, more background.
The car will probably just be a toy for street driving. I have the Camaro for Auto-X, but might take the Miata a time or two. So more than likely, I'll just use the car to surprise ricers, challenge friends, carve some country roads, etc.
Would any of you suggest I take an offer from someone and trade to a 25k mile used gt2560r w/ BEGi manifold and downpipe for my current setup?
Benefits vs. non-benefits?
I understand it'll be quicker spool, but does it fall flat up top? Should I even worry about that since I'll rarely see redline? What is the most boost/HP I could attain w/ a 2560r if I ever wanted to go faster (which seems to happen to all junkies)??
The car will probably just be a toy for street driving. I have the Camaro for Auto-X, but might take the Miata a time or two. So more than likely, I'll just use the car to surprise ricers, challenge friends, carve some country roads, etc.
Would any of you suggest I take an offer from someone and trade to a 25k mile used gt2560r w/ BEGi manifold and downpipe for my current setup?
Benefits vs. non-benefits?
I understand it'll be quicker spool, but does it fall flat up top? Should I even worry about that since I'll rarely see redline? What is the most boost/HP I could attain w/ a 2560r if I ever wanted to go faster (which seems to happen to all junkies)??
The 2560r will get you to 300whp if you ever decide you want more. It's not going to be cheap but; Paul has done it. Look for some of his threads.
#16
Hustler, 1 bar as in 15psi? And, I don't know what turbo you have, so if you could provide that info I could get the full picture.
I realize the quality of the BEGi parts is higher than my ebay parts, no doubt there, at least if the old saying "You get what you pay for" holds true.
I'm not sure if this person is wanting to trade a BEGi DP or just a custom one, that part wasn't made clear.
I guess the real question here is, being I'm wanting to stay on a tight budget w/ this car (for now anyway) and have no plans of rebuilding or upgrading the bottom end, which turbo would suit me better? My T3/T4 .63 A/R w/ OBX manifold, or a gt2560r w/ Begi mani? I wasn't really considering the trade at first because I just want to drive the car and not mess w/ anything I don't need to, but if this is widely suggested, maybe I'll spring for it.
EDIT: This is tough! Seems like some people don't mind lag, particularly those who live with it, and some people hate it; those who don't have to deal with it.
What is safer for the 175k mile bottom end? To roll into the boost, as with a smaller turbo? Or is it more of a boost is boost, it doesn't matter, kind of situation?
I realize the quality of the BEGi parts is higher than my ebay parts, no doubt there, at least if the old saying "You get what you pay for" holds true.
I'm not sure if this person is wanting to trade a BEGi DP or just a custom one, that part wasn't made clear.
I guess the real question here is, being I'm wanting to stay on a tight budget w/ this car (for now anyway) and have no plans of rebuilding or upgrading the bottom end, which turbo would suit me better? My T3/T4 .63 A/R w/ OBX manifold, or a gt2560r w/ Begi mani? I wasn't really considering the trade at first because I just want to drive the car and not mess w/ anything I don't need to, but if this is widely suggested, maybe I'll spring for it.
EDIT: This is tough! Seems like some people don't mind lag, particularly those who live with it, and some people hate it; those who don't have to deal with it.
What is safer for the 175k mile bottom end? To roll into the boost, as with a smaller turbo? Or is it more of a boost is boost, it doesn't matter, kind of situation?
#17
Let's see if I understand what you're saying. You're only talking about trading your turbo kit for the one you mention; right? If that's the case, I'd jump on that chance.
The 2560r will get you to 300whp if you ever decide you want more. It's not going to be cheap but; Paul has done it. Look for some of his threads.
The 2560r will get you to 300whp if you ever decide you want more. It's not going to be cheap but; Paul has done it. Look for some of his threads.
#18
I just want whatever will benefit me the most with a stock bottom end (thought it would be best to not pass 10 or 12psi if I plan on keeping the rods straight) and using the car on the street, where it will rarely see redline.
It seems like there is enough "want" for these 2560's that I could trade it later if I got bored with it, am I correct in thinking that?
It seems like there is enough "want" for these 2560's that I could trade it later if I got bored with it, am I correct in thinking that?
#19
Elite Member
iTrader: (22)
Join Date: Dec 2006
Location: Sunny Spanish speaking Non US Caribbean
Posts: 3,224
Total Cats: 3
FWIW, I've always thought that the 2554 is a little too small for our application but that's just my opinion; and you know what the say about opinions: "opinions are like belly buttons, everybody has one".