This seasons new ABSURDflow setup for my car
#41
Elite Member
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Done, I hope. It was nice to finally wash off the cutoff wheel dust. It sounds the same as it's always have, not a cool boxer-ish rumble of the other brand manifold posted earlier here in this thread. Oh well. I only drove it around my block twice to make sure there was no leaks and grind off the rust on the brake disks. So far it only makes about 3psi at 2000 whereas my previous manifold, my replacement BEGI/FM tubular manifold, would make 5 or so. I may go out to get a ritas and play with it. Or I may drink some beers.
ATP sent me a black silicone 90 instead of a blue which was even on the packing list in the box, oh well. I also have to throw on the toyota COPs, maybe.
ATP sent me a black silicone 90 instead of a blue which was even on the packing list in the box, oh well. I also have to throw on the toyota COPs, maybe.
#46
Elite Member
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,893
Total Cats: 399
The only sharp bend in the cold side piping is the black 90 silicone transition that is at the turbo outlet. Are you guys suggesting that it could cause my lack of low end torque?
I ran two 90's at the turbo outlet with my first tubular begi replacement mani back when I made 268rwhp and that felt peppy.
got torque?
The 'version 2' manifold felt more torquey than that setup, but I also redid the first section of I/C pipes. Never dynoed it however.
Intercooler piping pics:
Post I/C:
Or, having not driven the miata for half a year, I could just be used to the subaru's low end torque. That's probably the case. There's some things I have to check and I haven't brought her above 4500 yet, hell I've only put maybe a mile on it so far.
I ran two 90's at the turbo outlet with my first tubular begi replacement mani back when I made 268rwhp and that felt peppy.
got torque?
The 'version 2' manifold felt more torquey than that setup, but I also redid the first section of I/C pipes. Never dynoed it however.
Intercooler piping pics:
Post I/C:
Or, having not driven the miata for half a year, I could just be used to the subaru's low end torque. That's probably the case. There's some things I have to check and I haven't brought her above 4500 yet, hell I've only put maybe a mile on it so far.
#51
Elite Member
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,893
Total Cats: 399
There was a portable Dynojet dyno at Jesel's BBQ today. My DIY Ball/spring MBC, which is pretty damn close to 14psi on the street, could only muster to hold 9psi on the dyno. Just like the delaware dynojet, I can't make the same boost on a dyno as on the street, and we weren't allowed to tweak anything between our 2 runs. Soo at 9psi I did 249rwhp, dynojet, GT2560R. I reallllyyyy want to see what this will do at 14psi damnit.
#54
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
God damn Tim, that's impressive. I'm only making 242hp/230wtq at 12psi on a tater, but I'm under the curb and on low compression. Maybe I need to run 16 and flauce like a bauce, again.
#59
Elite Member
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,893
Total Cats: 399
I'll post a screenshot of the datalog. IIRC Peak at 12psi @ torque peak but droping steadily to 9psi at redline.
Youtube vid from a coworker.
I'll answer more questions and get the screenshots shortly.
Youtube vid from a coworker.
I'll answer more questions and get the screenshots shortly.
#60
Elite Member
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,893
Total Cats: 399
OK there's so much noise in my MAP sensor it's not funny. Eyeballing an average line between the peaks & valleys (~1psi spread) shows 13psi at 3550rpm140rwhp/210ftlb (350rpm higher than my last mt.net dyno day with the version 1 begi/fm tubular replacement mani).
That holds avg. 13psi to 5400rpm: 230hp/225ftlb.
Then it starts dropping to avg 11.5psi at 6000rpm which is my HP peak of 249hp/215ftlb. Torque is pretty much horizontal between 3500 & 6000 with max of 230 (94 head FTL).
From 6000 to 6800 it drops pretty sharply to 9psi. At 7200 I was at 8.5psi avg, 235rwhp and like 175ftlbs. Also at 120F IAT and 210coolant temps. My second run of 241hp was at 140IAT & 220coolant haha.
So I should have said I made 249rwhp @ 11.5 psi @ 6000rpm. Lo siento.
-or-
235rwhp @8.5psi @ 7200
If i can find my memory stick that works with windows 98 (or a new memory stick with win98 drivers ) I will transfer the screenshot of the log.
Again this manifold spools ~350 rpm slower than my version1 begi/fm replacement mani. While I never dynoed my version 2 while I had it (skidude's new mani), it felt quicker than the version 1. But this manifold feel better up top by a noticable amount, when it holds 14psi to 7200 on the street. So whatever.
That holds avg. 13psi to 5400rpm: 230hp/225ftlb.
Then it starts dropping to avg 11.5psi at 6000rpm which is my HP peak of 249hp/215ftlb. Torque is pretty much horizontal between 3500 & 6000 with max of 230 (94 head FTL).
From 6000 to 6800 it drops pretty sharply to 9psi. At 7200 I was at 8.5psi avg, 235rwhp and like 175ftlbs. Also at 120F IAT and 210coolant temps. My second run of 241hp was at 140IAT & 220coolant haha.
So I should have said I made 249rwhp @ 11.5 psi @ 6000rpm. Lo siento.
-or-
235rwhp @8.5psi @ 7200
If i can find my memory stick that works with windows 98 (or a new memory stick with win98 drivers ) I will transfer the screenshot of the log.
Again this manifold spools ~350 rpm slower than my version1 begi/fm replacement mani. While I never dynoed my version 2 while I had it (skidude's new mani), it felt quicker than the version 1. But this manifold feel better up top by a noticable amount, when it holds 14psi to 7200 on the street. So whatever.
Last edited by TurboTim; 07-01-2011 at 11:37 AM.