11.870 / 114.64 mph on Emanage Ultimate
10-17-2011, 02:16 PM
#1
Junior Member
Thread Starter
iTrader: (6)
Join Date: Oct 2005
Location: Atlanta GA
Posts: 335
Total Cats: 3
11.870 / 114.64 mph on Emanage Ultimate
Finally I went to drag strip with Locost Seven.
Based on -96 Miata, stock engine except exhintake cam, Garrett GT2560 turbo, 440 cc injector run by stock ECU and Greddy Emanage Ultimate piggyback.
Best 60' 1.736
Best trap speed 114.77
Best overall time 11.870 / 114.64 in quarter
Eight of a mile 7.596 / 93.01 mph
All these with Road Racing setup and tires having 1.5 to 2 degrees camber.
hrk
Based on -96 Miata, stock engine except exhintake cam, Garrett GT2560 turbo, 440 cc injector run by stock ECU and Greddy Emanage Ultimate piggyback.
Best 60' 1.736
Best trap speed 114.77
Best overall time 11.870 / 114.64 in quarter
Eight of a mile 7.596 / 93.01 mph
All these with Road Racing setup and tires having 1.5 to 2 degrees camber.
hrk
Reply
0
0
10-17-2011, 02:48 PM
#6
Junior Member
Thread Starter
iTrader: (6)
Join Date: Oct 2005
Location: Atlanta GA
Posts: 335
Total Cats: 3
Ben,
On that run 1.776 seconds.
These are the shoes MS3 will have to fill... After December 4th I will bug you guys further if I cannot get it sorted
Commerce is open on Fridays, for open cars make sure you bring hand restraints.
http://www.atlantadragway.com/
On that run 1.776 seconds.
These are the shoes MS3 will have to fill... After December 4th I will bug you guys further if I cannot get it sorted
Commerce is open on Fridays, for open cars make sure you bring hand restraints.
http://www.atlantadragway.com/
Reply
0
0
10-17-2011, 03:08 PM
#7
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Cool, I thought they had already shut down for the year. I'll see if I can get there this Friday, assuming I get the heater core replaced in my truck before then. :(
Reply
0
0
10-17-2011, 03:48 PM
#9
Junior Member
Thread Starter
iTrader: (6)
Join Date: Oct 2005
Location: Atlanta GA
Posts: 335
Total Cats: 3
Image from Crow Mountain, courtesy of Chuck Shultz
http://www.flickr.com/photos/k4cay/6...in/photostream
With me and in running condition ~1750 +- depending on gas level. Fuel Cell is 10 gallons. Not that much lighter than lightened Miata...
hrk
http://www.flickr.com/photos/k4cay/6...in/photostream
With me and in running condition ~1750 +- depending on gas level. Fuel Cell is 10 gallons. Not that much lighter than lightened Miata...
hrk
Last edited by hrk; 10-17-2011 at 04:15 PM. Reason: Cannot work the internet
Reply
0
0
10-17-2011, 04:31 PM
#11
Junior Member
Thread Starter
iTrader: (6)
Join Date: Oct 2005
Location: Atlanta GA
Posts: 335
Total Cats: 3
Road Racing takeoffs.
Hoosier 13/10x22 Radial slicks in 35 A compound.
It was wierd, The first trial run was 12.2 and from there on the car went slower, I had wheelspin in fourth gear way down the track, it felt like I had a flat tire. Pressure was good, and they were not corded. They seemed to have residue from glue, maybe that was building up and causing them to slip.
I changed tires to previously retired set and kept heating them more in the burnout area. They seemed to work without detoriating and I got continuous low 12 sec times.
I also dialed the rebound off from front shocks and ran them in 28 psi against normal 14 psi tire pressure.
hrk
Hoosier 13/10x22 Radial slicks in 35 A compound.
It was wierd, The first trial run was 12.2 and from there on the car went slower, I had wheelspin in fourth gear way down the track, it felt like I had a flat tire. Pressure was good, and they were not corded. They seemed to have residue from glue, maybe that was building up and causing them to slip.
I changed tires to previously retired set and kept heating them more in the burnout area. They seemed to work without detoriating and I got continuous low 12 sec times.
I also dialed the rebound off from front shocks and ran them in 28 psi against normal 14 psi tire pressure.
hrk
Reply
0
0
10-17-2011, 04:35 PM
#12
Elite Member
iTrader: (2)
Join Date: Sep 2008
Location: Central Florida
Posts: 2,799
Total Cats: 179
Very cool; as a guy who appreciates going fast in many forms, I've spent some time at the drag strip. I know sometimes track prep can make a big difference - especially depending on whether the track uses "run groups" (e.g. fast cars, slow street cars, bikes).
Reply
0
0
10-17-2011, 08:02 PM
#13
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
I got the truck's heater core replaced this evening, so I'm planning on hitting atlanta dragway on Friday in the Challenge Miata. At its current 2218 lbs with 6 gallons of gas and stock power, it might not lay down the most impressive times, but I want to wind it out. You going to be back there this Friday?
Reply
0
0
10-22-2011, 08:17 AM
#15
Junior Member
Join Date: May 2007
Location: Toronto Area, Ontario
Posts: 327
Total Cats: 95
Road Racing takeoffs.
Hoosier 13/10x22 Radial slicks in 35 A compound.
It was wierd, The first trial run was 12.2 and from there on the car went slower, I had wheelspin in fourth gear way down the track, it felt like I had a flat tire. Pressure was good, and they were not corded. They seemed to have residue from glue, maybe that was building up and causing them to slip.
hrk
Hoosier 13/10x22 Radial slicks in 35 A compound.
It was wierd, The first trial run was 12.2 and from there on the car went slower, I had wheelspin in fourth gear way down the track, it felt like I had a flat tire. Pressure was good, and they were not corded. They seemed to have residue from glue, maybe that was building up and causing them to slip.
hrk
Reply
0
0
10-22-2011, 08:34 AM
#16
Junior Member
Join Date: Jan 2008
Location: Atlanta, GA
Posts: 69
Total Cats: -1
I got the truck's heater core replaced this evening, so I'm planning on hitting atlanta dragway on Friday in the Challenge Miata. At its current 2218 lbs with 6 gallons of gas and stock power, it might not lay down the most impressive times, but I want to wind it out. You going to be back there this Friday?
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
FAB
Prefabbed Turbo Kits
216
03-22-2017 04:00 PM
