Miata Turbo Forum - Boost cars, acquire cats.

Engine Performance This section is for discussion on all engine building related questions.
Sponsored by:
Sponsored by: KPower

VVT swap CAS pinout question

Thread Tools
 
Search this Thread
 
Old 08-27-2015, 09:07 PM
  #1  
Junior Member
Thread Starter
 
Rwdturbo747's Avatar
 
Join Date: Feb 2015
Posts: 62
Total Cats: -1
Default VVT swap CAS pinout question
Was wondering if anyone knows the pinout for the 01+ CAS pictured below, I was wondering which pin is positive, ground, and signal. When I first did this engine swap I remember Sav or brain posting an image but I can't find it again for the life of me.

Also if anyone has a 99+ cas plug I'd like to buy it.

Attached Thumbnails VVT swap CAS pinout question-80-20150827_184956_c4f587769f2f70727c3677ef518d99e3041de93c.jpeg  
Rwdturbo747 is offline  
Reply
Leave a poscat 0 Leave a negcat
Old 08-28-2015, 08:33 AM
  #2  
Elite Member
iTrader: (6)
 
ryansmoneypit's Avatar
 
Join Date: Feb 2013
Location: A cave in Va
Posts: 3,395
Total Cats: 456
Default
I found my plug with a pigtail, for 10 bucks on ebay. the wiring is in the vvt megathread, first page I think.
ryansmoneypit is offline  
Reply
Leave a poscat 0 Leave a negcat
Old 08-28-2015, 09:53 AM
  #3  
Elite Member
iTrader: (10)
 
Reverant's Avatar
 
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,976
Total Cats: 355
Default
Originally Posted by Rwdturbo747
Was wondering if anyone knows the pinout for the 01+ CAS pictured below, I was wondering which pin is positive, ground, and signal. When I first did this engine swap I remember Sav or brain posting an image but I can't find it again for the life of me.

Also if anyone has a 99+ cas plug I'd like to buy it.
Please tell me that you were not trying to start the car all this time without the cam sensor connected.
Reverant is offline  
Reply
Leave a poscat 0 Leave a negcat
Old 08-28-2015, 10:45 AM
  #4  
Former Vendor
iTrader: (31)
 
Savington's Avatar
 
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,099
Default
In your picture, from left to right: +12v, Signal, Ground
Savington is offline  
Reply
Leave a poscat 0 Leave a negcat
Old 08-28-2015, 11:16 AM
  #5  
Junior Member
Thread Starter
 
Rwdturbo747's Avatar
 
Join Date: Feb 2015
Posts: 62
Total Cats: -1
Default
Originally Posted by Reverant
Please tell me that you were not trying to start the car all this time without the cam sensor connected.
No I'm checking my connections just to make sure I'm not missing anything else. The plug I had was also damaged.
Rwdturbo747 is offline  
Reply
Leave a poscat 0 Leave a negcat
Old 08-28-2015, 11:16 AM
  #6  
Junior Member
Thread Starter
 
Rwdturbo747's Avatar
 
Join Date: Feb 2015
Posts: 62
Total Cats: -1
Default
Originally Posted by Savington
In your picture, from left to right: +12v, Signal, Ground
Thanks sav
Rwdturbo747 is offline  
Reply
Leave a poscat 0 Leave a negcat
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
WTB MP62 (Hotside) (NB2)
Rick02R
WTB
3
01-03-2016 07:18 PM
Noob to Miataturbo from MA
JxPhan
Meet and Greet
3
10-02-2015 02:17 AM
Low oil pressure after 1.8 swap and new turbo setup
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM
VR6 to Miata Swap
ScrapinMX5
Meet and Greet
8
09-28-2015 01:04 PM
BP-6D on CAS only
aidandj
MEGAsquirt
14
09-25-2015 05:26 PM
Back to Subforum
Engine Performance
View Next Unread
Oil Cooler Sandwich Plate Will Not Fit With Factory Oil Warmer




Advanced Search
Quick Reply: VVT swap CAS pinout question


Reply Closed Thread Share

All times are GMT -4. The time now is 12:06 AM.