Flow

G'day folks,

I am trying to find a resource to ensure I have the correct part numbers for a rebuild on a 1.6 NB. The chassis number of the donor car for the engine is NB6C102098.
Essentially this is the rough shopping list at the moment. Any part numbers or suggestions would be helpful. I understand the NB 1.6 uses mostly 1.8 ancillaries. My New Engine? NB6 « omgpham?
Chassis is a Lotus 7 replica, use is track focused with solid, reliable 250whp on E85 with a 'stage one' head. ECU is a Motec M4.

Parts list - Progressively updated.
NB 1.6L Engine:
Oil Pump - BP6D-14-100
O-Ring - FE1H-14-122B
Gasket Oil Strainer - B6BF-14-248

Water Pump - Gates 42134
Assembly Gasket - B6BF-15-116
Inlet Pipe Gasket - B366-15-165
Water Pump Assembly Seal - B660-10-543B
O Ring - B61P-15-106A
Thermostat 180f - Stant 13868
Thermostat Gasket - B621-15-173

Alternator Belt - B6BF-18-381-9U (Gates)
Timing Belt - B597-12-205
Belt Tensioner - B660-12-700F
Belt Tensioner Spring - B660-12-711C
Idler Pulley - B660-12-730C

Valve Cover Gasket - B61P-10-235B
Valve Seal, Inlet - KL01-10-155
Valve Seal, Exhaust - KL02-10-155
Oil Pan Gasket, Front - B6F4-10-427
Oil Pan Gasket, Rear - B6F4-10-428
Front Main Seal - B3C7-10-602A
Rear Main Seal - BP05-11-312
Camshaft Seal - FS05-10-602A
Front Cover Gasket Lt - B61P-10-512
Front Cover Gasket Center - B61P-10-513
Front Cover Gasket Rt - B61P-10-514
Seal Plate Gasket - B61P-10-544
Manifold Gasket, Intake - B61P-13-111
Manifold Gasket, Exhaust - B695-13-460A

Bolt Lock-Flywheel - F201-11-511A
Crankshaft Pulley Bolt - B3C7-11-406
Crankshaft Pulley Bolt, Short Nose Crank - B630-11-406C

Pistons - 1.5 mm oversize - anything tight tolerance, 79.5mm JE custom maybe ?
Rods - Carrillo A Beam non stroker MA-323-1<A-55234H-04 or Maxpeeding H beams ?
Valves, Intake - Supertech MAIVN-1206 34x102.6 mm ?
Valves, Exhaust - Supertech MAEVI-1206 29x102.6 mm ?
Valve Guides - Miataroadster MR-BVG-16
Springs - Kelford KVS12 66lbs or ITM, Perfect Circle, Sealed Power. VS-855 (UPC 724956648306, OEM 418737, CLEVITE / PERFECT CIRCLE 212-1241, VS437, VS1065, W11454, Pioneer RV 1182) 66lbs or Eibach EVS Dual 66lbs or new BCs ?
Mazda Dual Spring Retainers - B6N7-12-123C, B6N7-12-113
Mazda Shim - 0000-01-531X-10 (1.10mm)
Mazda Shim Under Bucket Lifter - B6N7-12-18316
Cam - Kelford T203C 272/272 or Cat Turbo 269/249 with reduced base circle or split T203C/D 272/280 ?
Adjustable Cam Gears - Flyin Miata M04-66406
Main Bearings - ACL 5M8353H-.025
Rod Bearings - ACL 4B8351H-.025
Head Studs - APR 218-4701
Main Studs - APR 218-5401

Sensors - anything worth upgrading when running a Motec?
1999 - 2001 Protege 36-1 Crankshaft Pulley Plate - ZM01-11-408
Crankshaft Position Sensor - ZM01-18-221B

NB 5 spd Gearbox:
Short Shifter Kit - Miataroadster unbooted custom MR-SSK-NANB-5-4T-(Custom)-BR
Shift Bushing Kit - MIAD1033A Comprising:
Bushing - 0398-17-462A
Washer Wave - 8599-17-482
Shifter Bushing Washer - M505-17-482
Bushing - R502-17-492
Bush Change - R503-17-492

Front Oil Seal - H501-17-103
Front Cover Gasket - FE50-16-225A
Extension Housing Seal - M507-17-335A
Sensor Gasket - S524-17-112

themonkeyman

Where are you located? Why the NB 1.6 over a 1.8, especially if you'll be building and boosting it?

HarryB

From your list the only items that are 1.6-specific are the following:

Valve covers
Rebuild gasket kit (keep in mind that these usually include the head gasket; if you do not need it you may be better off ordering separate items rather than the complete kit)
Head gasket
Pistons
Valves (most probably, not 100%)

All else are the same between 1.6 and 1.8 NBs

huesmann

iTrader: (1)

OP is in NZ. Not sure if they have engine swap limitations in the Antipiodes, but that could be one reason.

Flow

Thanks VM guys, FYI the amount of fabrication work in the Lotus 7 replica for the 1.8 is the limiting factor.
Is there some where I can get part numbers from chassis numbers like this for BMW https://www.realoem.com/bmw/enUS/select Or maybe it might be possible to find the Mazda illustrated parts cataloger somewhere?

Here are some chassis numbers for NB donor cars:

NZ chassis number:
NB6C102098

UK Vins:
JMZNB186200410903
JMZNB186200134031

DaWaN

I use the website Mazda Electronic Parts Catalog - Free Mazda online parts catalog for EUDM specific parts. It has the 1600cc part numbers as well.

Flow

Thank you, that was very helpful. I have updated the OP with part numbers for the NB6s. Most of it is ordered now. I still have a few question marks around rods, pistons and top end hardware to deal with. Getting there. Special thanks to Six and Aidandj, cheers for help on side guys! Just magic.