Engine Performance This section is for discussion on all engine building related questions.
Sponsored by:
Sponsored by: KPower

CEL - P0304 troubleshooting? 2005 MSM

Thread Tools
 
Search this Thread
 
Old 10-19-2010, 03:51 AM
  #1  
Elite Member
Thread Starter
iTrader: (1)
 
rmcelwee's Avatar
 
Join Date: Jun 2005
Location: Pikeville, TN
Posts: 3,038
Total Cats: 27
Default CEL - P0304 troubleshooting? 2005 MSM

I posted this 31 hours ago on the MSM board. Of course there are no replies. I figure I'll get a few hits on here before I get home in the morning:


We are getting ready to take a little weekend vacation and haven't driven the MSM since Deals Gap (July). I fired it up today and it threw a P0304 (misfire on cyl#4). I am not around the car right now (haven't hardly been under the hood so I cannot remember what the COPs look like and how the wiring is) but my thoughts are to swap COPs (not sure which cyl# to swap it with) and see if I throw a code. If the code follows the COP I know it is a bad COP. If it doesn't then it might be the spark plug. Does this sound right? What else should I look at? Thanks!
rmcelwee is offline  
Old 10-19-2010, 10:54 AM
  #2  
mkturbo.com
iTrader: (24)
 
shuiend's Avatar
 
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,680
Default

Try switching out COP #4 with Cop #3 and see if it follows it. #4 is the one at the back next to the firewall.
shuiend is offline  
Old 10-19-2010, 11:33 AM
  #3  
Elite Member
iTrader: (11)
 
miatauser884's Avatar
 
Join Date: Feb 2009
Posts: 2,959
Total Cats: 11
Default

I believe a bad tank of gas can cause this. And .........I know that this will sound stupid. Unscrew your gas cap, and then screw it back in. Make sure that the gas cap is not loose.
miatauser884 is offline  
Old 10-19-2010, 04:02 PM
  #4  
Elite Member
iTrader: (11)
 
chicksdigmiatas's Avatar
 
Join Date: Apr 2008
Location: Texas, 'Murica
Posts: 2,497
Total Cats: 0
Default

I think the gas cap thing causes an EVAP code which is separate. A misfire in cylinder 4 is caused usually by ignition related components. Not knowing what you have done, I can't further stipulate. However, a cracked boot on your COP could cause this, as could a faulty plug, or a injector problem or vacuum leak in the area of the cyl4 runner could do such as well. A spark plug is cheap, soo... when you are switching coils around, switch it out. How many miles are on your current plugs?
chicksdigmiatas is offline  
Old 10-19-2010, 04:40 PM
  #5  
Elite Member
Thread Starter
iTrader: (1)
 
rmcelwee's Avatar
 
Join Date: Jun 2005
Location: Pikeville, TN
Posts: 3,038
Total Cats: 27
Default

Well, my wife must have a horseshoe up her ***. As I said, we are two days away from leaving town and the car wouldn't run. I swapped the coils and the code did not follow the swap. Then I swapped spark plug #1 and #4 and the code followed the swap. I can't see anything wrong with the plug but there must be a defect in it. Put in a set of NGK BKR5E-11 plugs (the best I could do on short notice) and the car runs fine.
rmcelwee is offline  
Old 10-19-2010, 04:57 PM
  #6  
Elite Member
iTrader: (11)
 
chicksdigmiatas's Avatar
 
Join Date: Apr 2008
Location: Texas, 'Murica
Posts: 2,497
Total Cats: 0
Default

Really? The parts store didn't stock 6's. Fail on their part. The only ones i have trouble with are the 7's
chicksdigmiatas is offline  
Old 10-19-2010, 05:36 PM
  #7  
Elite Member
Thread Starter
iTrader: (1)
 
rmcelwee's Avatar
 
Join Date: Jun 2005
Location: Pikeville, TN
Posts: 3,038
Total Cats: 27
Default

Yeah, I can live with them. If I start having problems I'll change them out.
$10 for an emergency fix isn't too bad!

The good news is that I picked up a Squier Mini at the pawn shop today (a rare one with a speaker <G>):



rmcelwee is offline  
Old 06-02-2014, 08:23 PM
  #8  
Elite Member
Thread Starter
iTrader: (1)
 
rmcelwee's Avatar
 
Join Date: Jun 2005
Location: Pikeville, TN
Posts: 3,038
Total Cats: 27
Default

Originally Posted by rmcelwee
Well, my wife must have a horseshoe up her ***. As I said, we are two days away from leaving town and the car wouldn't run. I swapped the coils and the code did not follow the swap. Then I swapped spark plug #1 and #4 and the code followed the swap. I can't see anything wrong with the plug but there must be a defect in it. Put in a set of NGK BKR5E-11 plugs (the best I could do on short notice) and the car runs fine.
So, 3.5 years and 700 miles later (I know, I really need to be driving the car more) I decided to drive the car to Walmart. I pull the car off the lift where it normally lives and the engine is missing like crazy. I put it back in the garage and drive the Geo to Walmart instead. A few days later (today) I read the codes. P0304 again. I'm going nuts at this point because I know I'm in for at least a new coil pack, at worst .... who knows. I pop the hood and get ready to pull the coils and run a compression check. What do I find? The #1 plug wire on the #4 coil is pulled off. Not loose - completely off. I have no idea why it is like that but I am one happy camper at this point (and my wife still has a horseshoe up her ***). I wish my auto tranny problem (some of you may have read my post about my V8 Miata tranny slipping) will be this easy to fix. I somehow doubt it will though.
rmcelwee is offline  
Reply
Leave a poscat -1 Leave a negcat
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM
nbdooey
Miata parts for sale/trade
9
08-30-2017 09:50 PM
tazswing
Race Prep
20
10-03-2015 11:04 AM
zephyrusaurai
Meet and Greet
2
09-28-2015 10:59 PM
Greasyman
General Miata Chat
2
09-28-2015 10:44 AM



Quick Reply: CEL - P0304 troubleshooting? 2005 MSM



All times are GMT -4. The time now is 01:35 PM.