160* Thermostat on '94
#1
160* Thermostat on '94
Installed 160* thermostat. After installing, I am idling at 2000 rpm even after the car warms up (5-10 minutes). I checked vacuum leaks, jumpered and checked idle screw, and rechecked that the 'stat was installed in the right direction. Is this simply because the Idle Speed Control Motor senses lower coolant temps due to the thermostat opening earlier? Car ran perfect prior to the change from 180* to 160* thermostat (180* is stock on the '94 correct?). Do I need to make any adjustments to accomidate the lower temp thermostat?
#5
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,020
Total Cats: 6,588
Actually, it's probably irrelevant. 2,000 RPM is much higher than the ISC system should ever reasonably target, even on a cold day on Neptune. And even if you are running at 160°F (which seems unlikely), that's pretty much the end of the warmup cycle anyway.
I'd go ahead and re-attach the vacuum hose that you disconnected and forgot about during the procedure.
According to the '92 FSM (the '94 should be more or less identical):
So, bearing in mind that the OEM thermostat actually has two valves, the smaller of the valves should begin to open between 182-188°F, the larger valve should begin to open at between 188-193°F, and both valves should be fully open by 212°F.
For purposes of comparison, this is roughly equivalent to an aftermarket thermostat with a rating of 195°F.
#6
Thanks Joe. I did a double check on the vacuum hoses visually, but I can go back and check my vacuum/boost gauge with the engine running (didn't do that the first time). My best bet will probably be to hit up the dealership on my way back to the garage this weekend to pick up a factory replacement....and be more weary of some of the advice I get.
#9
Something still isn't right. Went back to factory thermostat. The idle remains at 2000 rpm constant with or without the diagnostic box jumpered TEN & GRD after the car is warmed up.
The work I performed prior to this issue was just the thermostat replacement and grounding the LC-1 to the engine ground next to the idle air control motor. I don't think the ground would cause this, but maybe a wire popped loose for the idle air motor while I was fixing the ground???
The work I performed prior to this issue was just the thermostat replacement and grounding the LC-1 to the engine ground next to the idle air control motor. I don't think the ground would cause this, but maybe a wire popped loose for the idle air motor while I was fixing the ground???
#13
With a vacuum leak your motor will still pull the maximum vacuum possible for it's air supply and VE...thus the reason the revs climb with a leak. Your boost gauge could still show 25in hg vacuum, but that doesn't mean you don't have a BB-sized hole sucking air in somewhere. My gauge did wobble a bit more when I had a leak though...
While I understand your reasoning behind the thermostat being the only variable you changed, it is a variable which has minimal to no effect on your idle speed. As pointed out earlier, even 160* F is outside of warm-up range where the ECU plays with idle and enrichments, and even at that your 160* F thermostat isn't keeping the motor at that temp, but simply staying open at any temp above that.
Since this is the only manner in which your single supposed variable could possibly effect idle, and it's now out of the way, it's time to reassess the situation. Also, the fact that you reversed the modification, without change in idle speed, further supports the likelihood that there is a seperate, unrelated problem causing your high idle.
That problem is most likely a hole, somewhere in your intake tract at or after the throttle body, which your ECU is not in control of.
While I understand your reasoning behind the thermostat being the only variable you changed, it is a variable which has minimal to no effect on your idle speed. As pointed out earlier, even 160* F is outside of warm-up range where the ECU plays with idle and enrichments, and even at that your 160* F thermostat isn't keeping the motor at that temp, but simply staying open at any temp above that.
Since this is the only manner in which your single supposed variable could possibly effect idle, and it's now out of the way, it's time to reassess the situation. Also, the fact that you reversed the modification, without change in idle speed, further supports the likelihood that there is a seperate, unrelated problem causing your high idle.
That problem is most likely a hole, somewhere in your intake tract at or after the throttle body, which your ECU is not in control of.
#15
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
think about what happens when you crank the throttle, you're opening a valve allow the engnie to pull more air and thus allow it to increase RPMs. It cannot increase RPMs without increasing the airflow it ingests.
so you have a vacuum leak or you unplugged the idle valve when you fiddled around.
so you have a vacuum leak or you unplugged the idle valve when you fiddled around.
#17
Ok it is time to tap the brains of the gurus. I got out to the car today in the garage. Vacuum proved leakless, but I have a bigger problem I imagine:
I check the timing and the tick marks were no where in sight. Adjusting the CAS, the idle came back down around 1000rpm and I was able to see that the tick marks were 150-180* out of phase. Is this the sign of a slipped toof on the timing belt?
I check the timing and the tick marks were no where in sight. Adjusting the CAS, the idle came back down around 1000rpm and I was able to see that the tick marks were 150-180* out of phase. Is this the sign of a slipped toof on the timing belt?
#18
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,020
Total Cats: 6,588
It's also possible that the crank pulley itself has failed. The pulley is made in two halves separated by a rubber coupling, and I have heard (though never witnessed firsthand) that it's possible for the outer section, which is where the timing marks are, to rotate with respect to the inner section.
Remove the #1 spark plug, and also the oil dipstick. Insert the dipstick into the plug hole, and rotate the crankshaft clockwise by hand while observing the relative positions of the dipstick and the crank marks. The dipstick should reach the apex of its movement just as the timing mark comes to align with the 0 reference. If it does not, the crank pulley is bad. If it does, you're measuring something wrong.
It's entirely possible that the timing belt may have jumped a tooth or two, however that's not what is causing the timing marks on the pulley to appear 150-180° out under inspection with the timing light.
I'm also not sure that any of this is relevant to your idle speed problem. You're starting to change too many variables all at once here.
#19
The way my tests comes out on my posts is a lot less clear than the way I'm actually going about it. You're right about the timing. I had the wrong wire accidentally. Got the right wire, and timing is fine. I need to have a cup of coffee and stop thinking for a while. My brain hurts right now.
Going to borrow a multimeter later this week so that I can test the idle air motor.
Going to borrow a multimeter later this week so that I can test the idle air motor.
#20
I figured it out. The car's got a hotside MP62, so the throttle body is mounted relatively close to the brake lines against the firewall. Apparently something shifted and caused a very subtle interference between one of the lines and the throttle body. It was not shutting completely.
During the week, I removed the throttle body, cleaned it, and reset the TPS. I also checked the resistance on the idle air control motor; it was good. While reinstalling, I found the interference with the brake line. Temporarily, I have the brake line tweaked out of the way. It will be replaced by a brake proportioning valve, so the temporary fix will do.
Restarted the car and got the idle back to normal.
During the week, I removed the throttle body, cleaned it, and reset the TPS. I also checked the resistance on the idle air control motor; it was good. While reinstalling, I found the interference with the brake line. Temporarily, I have the brake line tweaked out of the way. It will be replaced by a brake proportioning valve, so the temporary fix will do.
Restarted the car and got the idle back to normal.