I love COPs
03-20-2008, 04:22 PM
#1
Elite Member
Thread Starter
iTrader: (7)
Join Date: Apr 2006
Location: VaBch, VA
Posts: 6,451
Total Cats: 322
I love COPs
Got mine today... along with the connectors to make it easy.
They're out of an 02 Corolla.
Still looking for a spare ignitor... but am gonna fab up the wiring harness in the meantime.
I'm also taking a look at the various ways of engineering the plate to hold them all in place.
They're out of an 02 Corolla.
Still looking for a spare ignitor... but am gonna fab up the wiring harness in the meantime.
I'm also taking a look at the various ways of engineering the plate to hold them all in place.
Reply
0
0
03-20-2008, 10:40 PM
#7
Sam I have 2 spare ignitors that I snagged from the u-pull-it. Lemme know if you need one.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Reply
0
0
03-21-2008, 09:44 AM
#10
Elite Member
Thread Starter
iTrader: (7)
Join Date: Apr 2006
Location: VaBch, VA
Posts: 6,451
Total Cats: 322
OK, since I'm going to source a spare ignitor to do this thing, is there room inside it to splice the Yel/Blu-Blk/Wht-Blue+1kohm... or are people putting the resistor somewhere in the harness?
Also, for the seperate ground wire protruding from the harness, should I ground it to the same grounding bundle I'm using for the MS/LC1... or should I find a seperate place on the head?
Also, for the seperate ground wire protruding from the harness, should I ground it to the same grounding bundle I'm using for the MS/LC1... or should I find a seperate place on the head?
Reply
0
0
03-21-2008, 10:26 AM
#11
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Reply
0
0
03-23-2008, 09:41 PM
#14
Elite Member
Thread Starter
iTrader: (7)
Join Date: Apr 2006
Location: VaBch, VA
Posts: 6,451
Total Cats: 322
Ben, I'm running Megasquirt "By Braineak" Standalone... sweet!
Anyways, just finished up the COP side of the harness, left about 5 feet extra to be sure I had enough to make it to the ignitor. My spare (to gut) ignitor should be here Tuesday. I'll be rocking this shiz by the weekend.
I've still gotta fab up a hold-down plate... working on the design.
Also, did anybody have to Dremel a little off the sides of the COP to get it to seat down completely. I think mine are about 1mm wider than the channel and they're not fully seated. I'm also looking forward to pulling the valve cover (to clean and affix studs) and checking the valvetrain on this magic 200k mile motor.
Anyways, just finished up the COP side of the harness, left about 5 feet extra to be sure I had enough to make it to the ignitor. My spare (to gut) ignitor should be here Tuesday. I'll be rocking this shiz by the weekend.
I've still gotta fab up a hold-down plate... working on the design.
Also, did anybody have to Dremel a little off the sides of the COP to get it to seat down completely. I think mine are about 1mm wider than the channel and they're not fully seated. I'm also looking forward to pulling the valve cover (to clean and affix studs) and checking the valvetrain on this magic 200k mile motor.
Reply
0
0
03-23-2008, 11:24 PM
#16
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
i dremeled the **** out of mine to fit the 01 cover. I also had the bosses for the original coils in the way but I didn't want to mod the valve cover to install the new setup. Now I might since I'll have a spare.
Reply
0
0
I'll remember to close my hood when it's raining. 
