mazdaspeed wiring diagrams?
10-03-2010, 02:21 PM
#1
Junior Member
Thread Starter
Join Date: Jan 2010
Location: madison, wisconsin
Posts: 47
Total Cats: 0
mazdaspeed wiring diagrams?
ive got an 04 msm and im lookin to see if anyone has a wiring diagram or could tell me which wire is the MAF signal wire so i can put my fuel cut defensor in and start walkin vettes instead of stayin next to em 
thnx guys!
thnx guys!
Reply
0
0
10-03-2010, 02:45 PM
#4
Junior Member
Join Date: Jun 2007
Location: Grayslake IL
Posts: 407
Total Cats: 2
Check on mazda-speed.com
The MAF is not the initial reason for the fuel cut. The ECU will cut power if the boost exceeds 11psi or so.
And as for walking vettes you are asking a lot out of that little IHI turbo.
The MAF is not the initial reason for the fuel cut. The ECU will cut power if the boost exceeds 11psi or so.
And as for walking vettes you are asking a lot out of that little IHI turbo.
Reply
0
0
10-03-2010, 03:01 PM
#5
Junior Member
Thread Starter
Join Date: Jan 2010
Location: madison, wisconsin
Posts: 47
Total Cats: 0
runnin 15 psi dnt hit fuel cut till then im just waitin for the piece to blow so i have an excuse to get the fm2 kit from flyin miata with a gt28 
otherwise the woman likes to complain when i spend money on "unnecessary" parts lol
otherwise the woman likes to complain when i spend money on "unnecessary" parts lol
Reply
0
0
10-03-2010, 04:32 PM
#6
Junior Member
Join Date: Jun 2007
Location: Grayslake IL
Posts: 407
Total Cats: 2
You don't need a full Fm2 kit. I would just buy the manifold turbo and downpipe. Make your own charge pipe to mate up with the factory charge pipes on the hot side and leave the cold side alone.
As for engine management you can now get a plug and play megasquirt.
As for engine management you can now get a plug and play megasquirt.
Reply
0
0
10-03-2010, 05:03 PM
#7
Junior Member
Thread Starter
Join Date: Jan 2010
Location: madison, wisconsin
Posts: 47
Total Cats: 0
my fault thats what i was getting at was what u listed, ive already got and intake and ic and a buddy of mine runs a machine shop so were making all hard pipes. i will admit ive been slackin on researching engine management so im not completly sure on what all will be useful to my setup in the spring and that will be best for future advancements
Reply
0
0
10-03-2010, 05:56 PM
#8
Junior Member
Join Date: Nov 2008
Location: Asheville, NC
Posts: 102
Total Cats: 1
The stock injectors max out at 12 psi & 93 octane gas. Water meth injection allowed me to run 14 to 15 psi with stock injectors & it was not too expensive. To walk a newer vett is asking a lot out of a mazdaspeed mx5 turbo.
You have to do boost cut bypass resistor mod to the boost sensor to get around the boost cut without getting a CEL. Or disconnect & plug the vacuum line going to the 3 way solenoid valve & boost sensor, but the CEL will come on.
You have to do boost cut bypass resistor mod to the boost sensor to get around the boost cut without getting a CEL. Or disconnect & plug the vacuum line going to the 3 way solenoid valve & boost sensor, but the CEL will come on.
Reply
0
0
10-04-2010, 09:09 PM
#9
Junior Member
Thread Starter
Join Date: Jan 2010
Location: madison, wisconsin
Posts: 47
Total Cats: 0
so ur telling me my gauge is liein to me? lol and water meth was another thing i was lookin at...buddy of mine said hed sell me his for pretty damn cheap but i dont see much of a point for street driving. but u know how long that usually lasts hahaha thanks for all the info guys
hahaha thanks for all the info guys
Reply
0
0
10-06-2010, 10:52 PM
#10
Junior Member
Join Date: Nov 2008
Location: Asheville, NC
Posts: 102
Total Cats: 1
so ur telling me my gauge is liein to me? lol and water meth was another thing i was lookin at...buddy of mine said hed sell me his for pretty damn cheap but i dont see much of a point for street driving. but u know how long that usually lasts hahaha thanks for all the info guys
hahaha thanks for all the info guysWater meth makes a huge difference in torque & hp. If you can get a water meth kit get one. What does it feel like? Each gear you go up it feels like it pulls harder & the higher up in the rpm it goes it feels like it pulls harder. 14.5 psi with water meth seems to be a sweet spot on my car.
http://www.youtube.com/watch?v=lwCE9OZSrwI
Reply
0
0
10-08-2010, 02:12 AM
#11
Junior Member
Thread Starter
Join Date: Jan 2010
Location: madison, wisconsin
Posts: 47
Total Cats: 0
Your gauge may be lying to you. I have pushed my car to its very limits before. When the atmospheric conditions were just right with 93 octane gas & TPS disconnected the most boost I could run was 12.25 lbs anything above that you will begin to hear the marbles in the cylinders sounds of detonation. If the atmospheric conditions were not just right I would have to turn my boost down to as low as 10.5 psi at times because I could hear detonation sounds.
Water meth makes a huge difference in torque & hp. If you can get a water meth kit get one. What does it feel like? Each gear you go up it feels like it pulls harder & the higher up in the rpm it goes it feels like it pulls harder. 14.5 psi with water meth seems to be a sweet spot on my car.
http://www.youtube.com/watch?v=lwCE9OZSrwI
Water meth makes a huge difference in torque & hp. If you can get a water meth kit get one. What does it feel like? Each gear you go up it feels like it pulls harder & the higher up in the rpm it goes it feels like it pulls harder. 14.5 psi with water meth seems to be a sweet spot on my car.
http://www.youtube.com/watch?v=lwCE9OZSrwI
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM
