IcantDo55

iTrader: (11)

Just installed and Ebay F1 racing stage 3 clutch with a Flyin Miata aluminum flywheel on my DD 2000. I like the clutch seems lighter than stock and works well. Little chattery but its new so I'll let it break in.

Question is now the car idles, choppy. Not smooth. Its not bad and I have put 400 miles on it and it works great I can only bet its due to the lack of rotating mass. Anyone else have this issue?

Thanks!

MartinezA92

iTrader: (4)

If nothing else has changed I could see it happening, MAYBE. I don't have that issue.
I don't think FM's flywheels are made of aluminum, btw. Just sayin.

IcantDo55

iTrader: (11)

Its def an FM flywheel.

Faeflora

iTrader: (2)

I have that flywheel with a different clutch and I had no problems after that. I think it wouldn't **** with the idle at all unless something isn't balanced and your crank is freaking out and your timing is getting fuxored somehow.

I say it's coincidental fuckage..

Oscar

iTrader: (2)

ACT Pro-Lite, no idle problems here, caused by the flywheel at least.

IcantDo55

iTrader: (11)

Hmmmm. It only has an issue at idle. I heard of this before with light flywheels. I'll call FM monday.

jim-NA

I've heard of people talking about this too. When I fitted a lightweight flywheel the only issue I had was the quicker drop in revs occasionally meant the engine would stall when approaching traffic lights, a small adjustment of the idle screw cured that.

what's your idle speed like?

mazpr

iTrader: (1)

I do not have an aluminum one, instead 5 pounds were removed from the stock steel FW.

The complete assembly, flywheel, disc, pressure plate were taken to a machine shop and everything was re-balanced just in case.

With the steel one with only 5 pounds off the revs do go down when approaching a traffic light, nothing crazy.

Like others say, its a matter of adjusting the idle.

IcantDo55

iTrader: (11)

750-850 1K with AC on

Bryce

iTrader: (24)

I've got the 1.6L 7lb Fidanza flywheel. I had to adjust my base idle (diag connector jumpered) up to 1000rpm. After that, no more stalling problems.

I'm in a heap of trouble now with the 2.0L. I've got the idle screw fully open and it idles just at 750rpm now.

Check your idle with GND and TEN jumpered in the diagnostic box.

mazpr

iTrader: (1)

On mine I took the FW to a machine shop for balancing, did you take yours to check before the install?

IcantDo55

iTrader: (11)

No, flywheel can from a member car and had no issues there and the clutch kit was new.

IcantDo55

iTrader: (11)

Ok so thinking about it I did install the head and the coolant reroute during the clutch install so to make sure I was not something I did I pulled off the timing belt and reset it. Seems better now, a little choppy but not what it was....so I'm going with the timing being off a little My bad.

hustler

iTrader: (6)

John and I put a 949 15lb clutch and it idles fine. Something could be out of balance and I suspect the ebay crap.

shlammed

iTrader: (8)

either that, or you didnt tighten your FW bolts enough and its vibrating like mad.

a friend of mine did that.

efe

Just another data point, I have that exact same flywheel w/ an ACT xtreme clutch. Absolutely no chatter, noise or any idle issues related to it.

NA6C-Guy

iTrader: (1)

It won't cause idle problems, but it WILL make any idle problems you had before more obvious. Mine did the same thing, went from pretty smooth to now having slight bumps at idle, feels like a misfire (but isn't). I can't find anything obviously wrong over the time I have had it rebuilt. I've also had this "issue" with other cars with light flywheels. Not really an issue, just a change in how it feels. You will get used to it. Makes you feel things you didn't feel before, normal or not.

astroboy

iTrader: (18)

I have a fidanza with spec puck clutch on a 1.8 that has no chatter and idled properly before and after turboing.

magnamx-5

iTrader: (7)

adjust your aic man it was set for more laod from the heavier flywheel probly and a few other parasitic losses you have remedied. If this doesnt work i call vacuum leak.