Reverant

iTrader: (10)

You still need the resistor, said wiring never reaches the MS somehow, so there is nothing that the MS2 can do to help in that direction.

jeff_man

iTrader: (7)

MS2 finally showed up.... Harness wires are so short

Times to start cutting and extending before i can install.

bigx5murf

iTrader: (5)

fedex tracking shows mine as not moving for 5 days? I really dislike fedex.....

FRT_Fun

iTrader: (19)

My fedex tracker is showing the same for an item I bought. I think they either broke the system, or something is seriously effed with fedex.

Reverant

iTrader: (10)

How longer would you prefer them to be? Genuine question here. I've installed two of these so far in local's cars and didn't have any problems with the wires being "short", however these being euro cars, the ECU location is the same as in the 90-93 cars.

Also, I would advise that you first test start the car before cutting and extending.

bigx5murf

iTrader: (5)

I was home all day friday waiting for another package, and tracking was working fine on the 23rd. But for this package, its been stuck on the 22nd.

jeff_man

iTrader: (7)

On a american nb the ecu is above the steering shaft. On my 99 it's fine as i will remove the stock ecu and everything else under the dash to lose weight and have easy access but the 02 the stock ecu will be left in for emotions testing easy switching.

But seeing as i'm going with the hot swap set up with my 99 and 02 and 2 different map tunes. I would need the ecu somewhere like the glove box or passenger side firewall to make it easy to quickly remove and install.

Which of these should i order?
http://www.diyautotune.com/catalog/m...ong-p-452.html
http://www.diyautotune.com/catalog/m...ong-p-101.html

Reverant

iTrader: (10)

You will need two of the normal (not the MS3X) wiring bundles, the top DB37 has 27 wires while the bottom one has 15 wires.

I would also recommend that you use TXL "thinwall" wiring instead - it is lighter, tougher and more flexible.

jeff_man

iTrader: (7)

I really only need to make the 02 harness longer. Can you give me a link to what your talking about or are you saying get http://www.diyautotune.com/catalog/m...ong-p-101.html

bigx5murf

iTrader: (5)

OK, so aside from FedEx phailing me hard... I need longer harness too? Or can I order an extension?

jeff_man

iTrader: (7)

I know the connectors are the expensive parts. That's why cutting and extending is more cost effective.

jeff_man

iTrader: (7)

b) Grey - Switchable tables. Connect this to a ground (through an on/off
switch) to switch between VE/Ignition tables.
c) Brown - Launch control. Connect this to a ground (through an on/off switch)
to switch launch control on/off.
d) Violet (purple) - Boost control low/high. Connect this to a ground

what if i'm not using any of these?

hustler

iTrader: (6)

At the least use switchable tables. I make a 91 octane table for you when you can't run 93.

Reverant

iTrader: (10)

Tape them away!

2manyhobyz

iTrader: (4)

Hi Rev,
Thanks for everything so far. I needed to know what boost control valve you would use so I can start sourcing one.
Happy New Year!

Reverant

iTrader: (10)

The one from DIYAutoTune.com works well!

jeff_man

iTrader: (7)

Cars starts on first try (with out the car in gear) and smokes like a 50s , running richer then the gauge can read. Have to remove a butt load of fuel.

hustler

iTrader: (6)

Be happy that it starts. I can make it run right in about 15 minutes. You're going to like this computer so much more than Failtronic.

Braineack

iTrader: (62)

don't do anything with them. Just tape them off so they cant accidentally touch a ground and trigger a switched table/launch.

jeff_man

iTrader: (7)

So hook then all to a 12v power?