New from CT, but no Miatas yet.. :(
#1
New from CT, but no Miatas yet.. :(
Hello, my name is drew and I just wanted to introduce myself. Been looking for a miata for a couple months but still haven't found one yet. Hoping there will be more f/s in the spring.
Have plans to turbo whatever I end up getting. I want to fab up most of the setup myself. I can tig weld and stuff so I shouldn't struggle to bad.
Current DD is a 08 mazdaspeed 3 with all the fixins. But that car is about finished with mods. Fully bolted, e85/meth, BNR 2871 turbo running 25psi reverse taper. It's a blast to drive and handles ok but I really want a miata as a true project car.
Have plans to turbo whatever I end up getting. I want to fab up most of the setup myself. I can tig weld and stuff so I shouldn't struggle to bad.
Current DD is a 08 mazdaspeed 3 with all the fixins. But that car is about finished with mods. Fully bolted, e85/meth, BNR 2871 turbo running 25psi reverse taper. It's a blast to drive and handles ok but I really want a miata as a true project car.
Last edited by Dsit995; 04-09-2014 at 08:13 PM.
#7
Thanks, been doing a lot of reading and planning. Originally I was thinking about using the k04 from my ms3 for the build, but I don't want to limit my turbo options down the road.
The manifold I want to make will be a t25/5 bolt exhaust setup.. Although if I did use my k04 I could always put my BNR on my miata.. Hmm that sounds like fun!
The manifold I want to make will be a t25/5 bolt exhaust setup.. Although if I did use my k04 I could always put my BNR on my miata.. Hmm that sounds like fun!
#15
Supporting Vendor
iTrader: (1)
Join Date: Sep 2010
Location: Lake Forest, CA
Posts: 7,950
Total Cats: 1,003
Point is, you're a noob. It's like showing up to a party and, without even going inside, start welcoming people as they walk in the door. You ain't part of the party yet, so just going around welcoming people raises suspicion.
#19
We'll after 6 weeks of part gathering and finally passing emissions, I'm finally ready to start my build.
Current list of parts:
MS2e (rev built)
FIC 650cc injectors
Efr 6258
Flanges and 3" 304 for DP and 2.5" 304 for the rest of the exhaust
Flowmaster muffler
Obx resonator
Schedule 10 1.5" weld els for manifold
Vbands for entire exhaust
And bunch of other small bits, aluminum piping,intercooler, boost AFR EGT gauges, methanol setup, diy COPs setup
Still on my list of things to get in a stg1 FM clutch, fuel pump, radiator
Just started building my collector for the manifold, going to take some pics and start my build thread..
Modest goals to start, looking for 200whp and trying to find a spare block that I can start building for when the current motor taps out
Current list of parts:
MS2e (rev built)
FIC 650cc injectors
Efr 6258
Flanges and 3" 304 for DP and 2.5" 304 for the rest of the exhaust
Flowmaster muffler
Obx resonator
Schedule 10 1.5" weld els for manifold
Vbands for entire exhaust
And bunch of other small bits, aluminum piping,intercooler, boost AFR EGT gauges, methanol setup, diy COPs setup
Still on my list of things to get in a stg1 FM clutch, fuel pump, radiator
Just started building my collector for the manifold, going to take some pics and start my build thread..
Modest goals to start, looking for 200whp and trying to find a spare block that I can start building for when the current motor taps out
Thread
Thread Starter
Forum
Replies
Last Post