$40 wideband
06-21-2007, 11:56 AM
#1
Newb
Thread Starter
Join Date: Jun 2007
Posts: 26
Total Cats: 0
$40 wideband
Any of you use this? Not bad for the price. Granted, it wont have top end resolution, but its leagues better then a NB and even cheaper then some of them.
http://www.14point7.com/JAW/JAW.htm
http://www.14point7.com/JAW/JAW.htm
Reply
0
0
06-21-2007, 05:59 PM
#3
Newb
Thread Starter
Join Date: Jun 2007
Posts: 26
Total Cats: 0
sorry, guess im not quite used to the search.
I say that because the designer himself admited that it does not calculate. Instead it looks up values, so it shows say 14.73 and then 15.37 but nothing in between.
Still, this is far better than any NB and most user wont notice.
I say that because the designer himself admited that it does not calculate. Instead it looks up values, so it shows say 14.73 and then 15.37 but nothing in between.
Still, this is far better than any NB and most user wont notice.
Reply
0
0
06-22-2007, 09:22 AM
#5
Senior Member
Join Date: Jul 2005
Posts: 513
Total Cats: 0
Agreed.... I have one ready to be picked up actually.... There was a group buy on the local board here. Hopefully, I'll be able to get it installed next week... if I can get a bung put on the exhaust......
Dave,
Dave,
Reply
0
0
06-22-2007, 01:35 PM
#6
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,483
Total Cats: 4,076
all it does it take the sensors readings, and outputs them. How can it not read between 14.7 and 15.3? the sensors output is linear, there not much to it. it shoudl work jsut as good as any other WBO2 controller out there.
Reply
0
0
06-22-2007, 02:17 PM
#7
Newb
Thread Starter
Join Date: Jun 2007
Posts: 26
Total Cats: 0
Yes the output is there, but the controller he programmed is not the best. I mean, granted, if your looking at this thing your not looking for the best. It does GREAT, its just an interesting tidbit.
He states that it uses look up tables and not calculations.
http://msefi.com/viewtopic.php?t=26503
He states that it uses look up tables and not calculations.
http://msefi.com/viewtopic.php?t=26503
Reply
0
0
06-23-2007, 02:48 AM
#9
Junior Member
Join Date: Jun 2005
Location: Huntington Beach, CA
Posts: 354
Total Cats: 0
You can't edit the first two columns within the software. Hopefully he'll update the firmware so that this could be an option, which doesn't seem too bad because it's just changing the constant values that already exist to variables input in the same matrix where Vout1 and Vout2 can be input. Of course he'll have to worry about available memory on the chip.
Reply
0
0
06-23-2007, 03:34 AM
#10
Elite Member
iTrader: (10)
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,976
Total Cats: 355
$45+$70 for the sensor = $115. You can get an LC-1 for $180-$190 on ebay. I would just skip this one unless I had to have 1 sensor per cylinder on a V8 (or I really didn't care about accuracy and I couldn't affor 70-80 more bucks).
Jim
Jim
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
Mikel
MEGAsquirt
4
09-28-2015 04:46 PM
