Question about CMP and CKP signal mods...
#1
Question about CMP and CKP signal mods...
Braineak built my MS and I've got it running but am planning to move to the Hi-Res firmware and put in my 550cc injectors in prep for adding the turbo afterwards. I wanted to make sure these mods were done to my MS so I busted it open and I've been searching around and see from this page: How to MegaSquirt your Mazda Miata
the section: -How to mod a MegaSquirt-I PCB2.2 ECU-
It looks like the CMP mod was done, but I'm not so sure about this part:
"CKP Signal" -- We just need a 12v pullup. Install a 470ohm 1/4w resistor between the right side (non-band) end of D5 and the right hole (banded) end of D9.
Looking at my board nothing is wired into the diode in D5 but I just wanted to make sure it wasn't done some other way I'm not aware of. Also, I found this thread: https://www.miataturbo.net/forum/t25383/ at the bottom Joe says:
"Make sure that you have no jumpers installed on the MS PCA in either TSel or TachSelect."
Looking at my board there is a jumper between TachSelect and "Optoin". Should I remove this? And can you tell by looking at my board if I still need to do the CMP Signal mod-sorry about the pic, best I could do, my camera is old. Thanks!
the section: -How to mod a MegaSquirt-I PCB2.2 ECU-
It looks like the CMP mod was done, but I'm not so sure about this part:
"CKP Signal" -- We just need a 12v pullup. Install a 470ohm 1/4w resistor between the right side (non-band) end of D5 and the right hole (banded) end of D9.
Looking at my board nothing is wired into the diode in D5 but I just wanted to make sure it wasn't done some other way I'm not aware of. Also, I found this thread: https://www.miataturbo.net/forum/t25383/ at the bottom Joe says:
"Make sure that you have no jumpers installed on the MS PCA in either TSel or TachSelect."
Looking at my board there is a jumper between TachSelect and "Optoin". Should I remove this? And can you tell by looking at my board if I still need to do the CMP Signal mod-sorry about the pic, best I could do, my camera is old. Thanks!
#3
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,019
Total Cats: 6,587
Also, I found this thread: https://www.miataturbo.net/forum/t25383/ at the bottom Joe says:
"Make sure that you have no jumpers installed on the MS PCA in either TSel or TachSelect."
"Make sure that you have no jumpers installed on the MS PCA in either TSel or TachSelect."
#5
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,490
Total Cats: 4,079
Braineak built my MS and I've got it running but am planning to move to the Hi-Res firmware and put in my 550cc injectors in prep for adding the turbo afterwards.
It looks to me like you have the pullup on D1, it was just taken from somewhere other than D9.
what are the two wires you have attached to what looks to be the boot jumper?
Thread
Thread Starter
Forum
Replies
Last Post
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM