What is this stumble?
#1
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
What is this stumble?
So I've got some kind of stumble when I stomp on it at about 60mph in 6th gear. It never did this before when I had the 5-speed, but since then I replaced the transmission, and had the engine out, and re-did a bunch of vacuum lines, and removed some emissions crap, and cleaned a lot of stuff.
Thoughts on what could cause this? I attached a quick log of it happening, and the msq I'm using now.
Thoughts on what could cause this? I attached a quick log of it happening, and the msq I'm using now.
#4
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
I have another log that I took that day that may have more info. The only thing I can see that fluctuates is RPM and "engine". I don't really know what "engine" is, but I suspect that is the problem, and is somehow causing RPM to fluctuate as well. Thoughts?
I am also going out now with some det cans and I will try to get another log, though I don't suspect it will be much different.
I am also going out now with some det cans and I will try to get another log, though I don't suspect it will be much different.
#6
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
I'm on the Alpha10 firmware from last summer, my MAP line is T'd off the cruise control line, and I'm not sure what my lag factor settings are, I don't know where to find those.
#9
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
I think im in the 50s for everything still.
I was seeing around 50-60 TPSdot at idle at the same lag factor, with the new firmware, I see 4.
but 50 on this firmware is like 0 on the older ones. (where 0 is the most filtering)
I was seeing around 50-60 TPSdot at idle at the same lag factor, with the new firmware, I see 4.
but 50 on this firmware is like 0 on the older ones. (where 0 is the most filtering)
#13
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
there's a bunch of new idle code stuff that you can turn on (base duty table, voltage correction table, timing correction table). I just upgraded from alpha11, but I dont have VVT, where I know there were improvements there too but I just loaded my alpha11 map and turned on/tuned all the idle features.
BUT IIRc, alpha10 had different PID code, so you might have to retune those values...is your idle code PID parameters in the low double digits or the triple?
BUT IIRc, alpha10 had different PID code, so you might have to retune those values...is your idle code PID parameters in the low double digits or the triple?
#14
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
Idle PID are 25, 30, and 0.
So I'll update to Beta20 this week, but I am still skeptical that that will fix my problem, since I was running Alpha10 last year and didn't have this problem. I did move where my map signal is coming from... it was t'd off the cruise line right by the manifold last year, now it's T'd much closer to the cruise solenoid... would that cause this?
So I'll update to Beta20 this week, but I am still skeptical that that will fix my problem, since I was running Alpha10 last year and didn't have this problem. I did move where my map signal is coming from... it was t'd off the cruise line right by the manifold last year, now it's T'd much closer to the cruise solenoid... would that cause this?
#18
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
there's a comprehensive change log so you know what to change from alpha 10 to beta 20. you'll want to get beta 21 as soon as it is out too but the changes are minor from 20 (just dont run negative enrichments in your "new" throttle pump AE).
lag factor of 100 is basically no filtering. with the new code you can almost run that. it's pretty awesome and responsive.
lag factor of 100 is basically no filtering. with the new code you can almost run that. it's pretty awesome and responsive.