MegaSquirt install - turns over, won't start.
03-02-2011, 06:57 PM
#1
Elite Member
Thread Starter
iTrader: (6)
Join Date: Sep 2010
Location: Seattle, WA
Posts: 3,611
Total Cats: 25
MegaSquirt install - turns over, won't start.
All right. Just installed my MegaSquirt2 (V3 board) today, everything reads out as expected on TunerStudio.
Go to start it, it turns over nice and healthily, but it won't start. Fuel pump is on and getting fuel pressure there. Swapping over to the stock ECU, it starts fine.
Looking for advice on what I did wrong with the attached basemap and log - as it's basically the DIYAutotune basemap however, I'm not sure what would be wrong with it.
Thank you!
(Edit) Specs:
Stock '91 1.6 with AFM and no mods yet.
Go to start it, it turns over nice and healthily, but it won't start. Fuel pump is on and getting fuel pressure there. Swapping over to the stock ECU, it starts fine.
Looking for advice on what I did wrong with the attached basemap and log - as it's basically the DIYAutotune basemap however, I'm not sure what would be wrong with it.
Thank you!
(Edit) Specs:
Stock '91 1.6 with AFM and no mods yet.
Last edited by blaen99; 03-02-2011 at 07:09 PM.
Reply
0
0
03-02-2011, 07:25 PM
#5
Elite Member
Thread Starter
iTrader: (6)
Join Date: Sep 2010
Location: Seattle, WA
Posts: 3,611
Total Cats: 25
Unfortunately, that's how it was loaded in my Tunerstudio Ben.
To say the least, I'm befuddled as to how that would happen.
(Edit) Looking closer at this, I have no idea how that basemap was imported that way. Does someone have a MS2Extra 2.1 basemap they could point me towards, to see if this is duplicable behavior?
To say the least, I'm befuddled as to how that would happen.
(Edit) Looking closer at this, I have no idea how that basemap was imported that way. Does someone have a MS2Extra 2.1 basemap they could point me towards, to see if this is duplicable behavior?
Reply
0
0
03-03-2011, 01:01 PM
#12
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
It looks built okay, but the tach input mods so see on the underside were for the MS-I inputs. It needs to be modified so the MS2 can get the CAS signals.
are you handy with an iron?
are you handy with an iron?
Reply
0
0
03-03-2011, 01:06 PM
#14
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
do this:
the yellow wires need to be added and go to the LED pins that the small length of black wire attach to. I just realized there's no spark outputs either. lolz
the yellow wires need to be added and go to the LED pins that the small length of black wire attach to. I just realized there's no spark outputs either. lolz
Reply
0
0
03-03-2011, 03:30 PM
#19
Elite Member
Thread Starter
iTrader: (6)
Join Date: Sep 2010
Location: Seattle, WA
Posts: 3,611
Total Cats: 25
That and to fix my shitty harness job.
Better in Brain's hands at this point then mine, I'd have to rush the build like mad instead of putting in a working MS and working on the damn car.
Better in Brain's hands at this point then mine, I'd have to rush the build like mad instead of putting in a working MS and working on the damn car.
Reply
0
0
03-03-2011, 04:50 PM
#20
Elite Member
iTrader: (1)
Join Date: Jun 2006
Location: Warrington/Birmingham
Posts: 2,642
Total Cats: 42
I like the complete absence of ignition outputs on that board.
Seller failed miserably at building the MS properly. Unlucky OP, but at least you've got Brain to fix it for you
Seller failed miserably at building the MS properly. Unlucky OP, but at least you've got Brain to fix it for you
Reply
0
0
