Injector connector/plug
05-22-2007, 05:10 PM
#1
Junior Member
Thread Starter
Join Date: Aug 2005
Location: So Cal
Posts: 125
Total Cats: 0
Injector connector/plug
Where can I buy fuel injector connectors/plugs for my stock miata injectors?
I dont want to hack into the factory injector wiring so i would rather buy new connectors and make my own wiring.
TIA
I dont want to hack into the factory injector wiring so i would rather buy new connectors and make my own wiring.
TIA
0
05-22-2007, 06:05 PM
#4
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
i wasn't able to remove the FI harness from my car. one of its connectors is behind the head, and I was afraid that I would not be able to reconnect it to the new harness. so I put new injector clips on my original harness. took 10 minutes to make the 8 connections, plus another 5 to tape it all up to look like stock.
0
05-22-2007, 06:12 PM
#6
Junior Member
Thread Starter
Join Date: Aug 2005
Location: So Cal
Posts: 125
Total Cats: 0
I want to use my existing injectors and I want to make a dedicated wiring harness for the injectors that would be connected to my megasquirt system.
0
05-22-2007, 06:17 PM
#9
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,490
Total Cats: 4,079
i think he has injectors other than the oem ones....
it's easier just to wire in the pigtails...then just use the ones you need. so you have a total of 8 clips, but 4 injectors...
it's easier just to wire in the pigtails...then just use the ones you need. so you have a total of 8 clips, but 4 injectors...
0
05-22-2007, 07:32 PM
#13
I have a stock injector harness (not sure if it's the 94 or the 2000 o.O) that I think I'm going to cannibalize for the plug that interfaces to the main harness. I suppose I could sell the stock connectors (actually, I could sell pretty much the whole harness minus the connector at the end). What's your budget?
-Mike
-Mike
0
05-22-2007, 08:37 PM
#14
Junior Member
Thread Starter
Join Date: Aug 2005
Location: So Cal
Posts: 125
Total Cats: 0
I have a stock injector harness (not sure if it's the 94 or the 2000 o.O) that I think I'm going to cannibalize for the plug that interfaces to the main harness. I suppose I could sell the stock connectors (actually, I could sell pretty much the whole harness minus the connector at the end). What's your budget?
-Mike
-Mike
0
05-22-2007, 08:39 PM
#15
Junior Member
Thread Starter
Join Date: Aug 2005
Location: So Cal
Posts: 125
Total Cats: 0
Lets simplify the question:
I am looking for injector connectors. where can i buy them?
I dont want to cut and plice into the existing factory injector wiring harness.
that was easy!
I am looking for injector connectors. where can i buy them?
I dont want to cut and plice into the existing factory injector wiring harness.
that was easy!
0
05-22-2007, 08:51 PM
#17
Just pull them from the car that has the injectors you want. but seriusly unless you want to run some non PNP injectors why change. And if you are then why does 8 wire splices scare you so we run batch fire injection geez. The harness comes off the car easily, and the wires are just wires. Why make more work?
0
05-22-2007, 09:01 PM
#19
Junior Member
Thread Starter
Join Date: Aug 2005
Location: So Cal
Posts: 125
Total Cats: 0
0
