wittyworks

iTrader: (6)

Hey guys, I just came in from trying to start my diypnp on my 95 miata with sequential injection. I couldn't get it to start, only stutter. I found two problems that i have, and i don't know if they're related to my tunerstudio tune or my wiring.

Two problems are:

1. AEM UEGO isn't connecting to laptop/ecu. I have the white wire from the aem wired into pin 1 of my db15 connector, and I believe that is connected to the 02 inside my box.

2. Bigger problem: Only cylinder 1 and three are getting gas. 1 and 3 plugs are wet, 2 and 4 are dry. I am running sequential injection with id1000 injectors. Req fuel set at 3.1 according to calculator with 1839 cc 4 cylinders 1000 cc injectors

What I Know:
All four cylinders are getting spark
I have the sequential injection chip set up inside, so maybe im missing a setting for that somewhere.

I am posting up my msq. and will post my excel jumper spreadsheet in a sec.

Thanks for all the help bros.

wittyworks

iTrader: (6)

Okay here is my jumper set up spreadsheet. I also changed all my iginition settings to the settings on this page, didn't help at all.

As a side note, where do i go to set the timing to make sure it's at 10, like i had to do with the mspnp? Or do i not need that step with ms2?

wittyworks

iTrader: (6)

Okay i figured out the wb02 problem. Now just have to deal with the two non firing injectors.

Did i need to wire a 12v and a ground to the spots on the sequential add on board?

wittyworks

iTrader: (6)

I think i only would have needed that for low impedance injectors.

Going to sleep now, waking up early tomorrow to start messing with it before school, hopefully someone wants to help me!! I think it is a simple problem that i'm overlooking.

Braineack

iTrader: (62)

map is not setup for seq. injection. so it's not trying to fire 3 then 2.

bearda

It's not clear from your jumper spreadsheet if you got this or not, but make sure you're running two jumpers off the sequential ignition board over to your INJ3 and INJ4 outputs, as well.

You do need to set the 10 degree base timing, just like the MSPNP.

wittyworks

iTrader: (6)

Thank you sir, i was thinking is something like this. Any tips or hints on how i should go about fixing this?

to bearda:

I do have a wire for each injector, i know its hard to tell from my excel but
inj1-4u
inj2-4y
inj3-4z
inj4-4v

Braineack

iTrader: (62)

turn on the additional drivers in the seq. injection menu.

wittyworks

iTrader: (6)

I was trying to do that last night, to change it from "standard drivers" to "additional drivers" but my drop down menu for that has no options.

Braineack

iTrader: (62)

doesnt the 94-95 basemap package come with a seq. setup msq?

wittyworks

iTrader: (6)

I guess I'll try to reload the base map and see if the drop down menu appears.

wittyworks

iTrader: (6)

I just tried to re-download the msq, and i found a problem. It says it cant find the controller definition file for signature: MS2ExtraRel 3.0.3h. The ecu definition on my tune is MS2Extra Serial310. I couldnt find out where to download the specific 3.0.3h firmware before.

Braineack

iTrader: (62)

ignore the issue, click okay.

you should be loading 3.1.3 if anything.

wittyworks

iTrader: (6)

Its not letting me open the file. This is when im trying to open it in tunerstudio. Ive tried opening into its own temp file as well as a previously saved file. The window says "Can not find the controller definition file (ini,ecu) for Signature:MS2Extra Rel 3.0.3h
Please select the appropriate configuration file"

Thanks for helping me brain and sorry if im doing stupid things.

Braineack

iTrader: (62)

how are you opening the file?

typically, when I have a project open, and I'm opening a msq it was say the file you are loading doesn't match your project's firmware, yada yada do you want to convert? click okay.

sounds like you are opening this through windows, and letting it open in a temp project, but you dont have the firmware installed locally.

anyways: http://msextra.com/doc/ms2extra/files/alpha/

should be the ms2extra_alpha20090912.zip one

wittyworks

iTrader: (6)

SWEET!!!
Okay so now i have the correct startup map loaded into tunerstudio, using that ecu definition you just told me. Now i have to reload the correct firmware form that file onto the ecu, using "download-MS2-firmware.bat" correct?

Thanks brain youre a boss

Braineack

iTrader: (62)

I'd still want at least the latest release loaded on my MS, which is 3.1.1: http://msextra.com/doc/ms2extra/files/release/

But really I'd load 3.1.3 personally.


Regardless, you shouldn't have to reflash the MS to load the map, you just need the fimware locally so it knows what to do with it.

wittyworks

iTrader: (6)

Thanks brain, i think i got everything figured out and reloaded, drop down menu is now available. Ill post back in here after i try to start it again.

Let me know if you ever need anything welded, you have helped me a lot on getting this setup.

Braineack

iTrader: (62)

w00t!

wittyworks

iTrader: (6)

It started!!! Got it started using the gas pedal, need to add some fuel but im late to school now because the miata is the main rioroty this morning!

SO PUMPED!!! LETS GET THIS EFR SPOOLIN!