code version does not match signature
#1
Junior Member
Thread Starter
iTrader: (7)
Join Date: Mar 2007
Location: Texas Panhandle
Posts: 211
Total Cats: 0
code version does not match signature
So I finished my MegaSquirt(MSI ver 3.0) Standalone build for my 97. I start getting ready to load the software and was following Brain's FAQ. I loaded the the MSnS+Extra Hi-Res code with the boot pin jumpered, and had no problems. A little over 1700 records loaded. Opened MegaTune and got the following error message:
Tried loading Low Res code also and got the same issue. Every time the spaces were replaced with ` or occasionally I got @ in place of spaces. I tried this with the stim and in the car.
MSII Downloader was logging this on two different loads:
I thought it might be an issue with the usb-to-serial adapter so I took it to work. I have a desktop computer that has a serial port, and I have a straight through serial cable. This is the same setup I used to test everything during the build process. I thought possibly it was a communication issue with the usb-to-serial adapter. Not so, I got even more garbage for signatures.
I found a few other threads with similar error messages, and followed the advice to no solution.
At this point I am thinking I need to resolder the serial communication circuit and hit the whole board with flux cleanner. I have not taken the flux off yet. I am hoping some other people have more ideas though.
I followed the megamanual for the build and tested along the way. I did the Miata related mods according to the DIYAutoTune website. When I was loading the firmware my serial data rate was 9600. If there are any details I am forgetting let me know. Sorry for the long post.
Controller code version does not match signature in MSnS-extra.ini.
(See audit.log for where the above file was found.)
Expected "MS/Extra format hr_10 **********" (found in ini file)
Received "MS/Extra`format`hr_10`**********" (from controller)
Table corruption may occur, this is usually a very serious problem.
Terminate MegaTune now?
(See audit.log for where the above file was found.)
Expected "MS/Extra format hr_10 **********" (found in ini file)
Received "MS/Extra`format`hr_10`**********" (from controller)
Table corruption may occur, this is usually a very serious problem.
Terminate MegaTune now?
MSII Downloader was logging this on two different loads:
Writing:
Write complete, 1774 records, 28036 bytes.
Verifying:
Signature: "MS/Extra`format`hr_10`**********"
Verify complete.
Elapsed time: 86.38 seconds
Write complete, 1774 records, 28036 bytes.
Verifying:
Signature: "MS/Extra`format`hr_10`**********"
Verify complete.
Elapsed time: 86.38 seconds
Writing:
Write complete, 1774 records, 28036 bytes.
Verifying:
Signature: "MS/Extra`format@hr_10`**********"
Verify complete.
Elapsed time: 82.89 seconds
Write complete, 1774 records, 28036 bytes.
Verifying:
Signature: "MS/Extra`format@hr_10`**********"
Verify complete.
Elapsed time: 82.89 seconds
Writing:
Write complete, 1774 records, 28036 bytes.
Verifying:
Signature: o@`qp@jjjjJjjJjj
Verify complete.
Elapsed time: 85.64 seconds
Write complete, 1774 records, 28036 bytes.
Verifying:
Signature: o@`qp@jjjjJjjJjj
Verify complete.
Elapsed time: 85.64 seconds
Writing:
Write complete, 1774 records, 28036 bytes.
Verifying:
Signature: O`@qp`jjjjjjJjjj
Verify complete.
Elapsed time: 84.85 seconds
Write complete, 1774 records, 28036 bytes.
Verifying:
Signature: O`@qp`jjjjjjJjjj
Verify complete.
Elapsed time: 84.85 seconds
At this point I am thinking I need to resolder the serial communication circuit and hit the whole board with flux cleanner. I have not taken the flux off yet. I am hoping some other people have more ideas though.
I followed the megamanual for the build and tested along the way. I did the Miata related mods according to the DIYAutoTune website. When I was loading the firmware my serial data rate was 9600. If there are any details I am forgetting let me know. Sorry for the long post.
Thread
Thread Starter
Forum
Replies
Last Post