can't get ms2 to work on jimstim
#1
can't get ms2 to work on jimstim
Well I've just finished building my ms2 and jimstim (I think I've finished...)
In tuner studio I can get all the MAT/CLT/TPS etc working. Can't seem to get the tach working.
Seem to have settings correct but no tach reading. If I set input capture to rising edge (which isn't correct anyway) then I do get a crazy erattic jumpy reading on the tach. With falling edge I get no reading at all. Also tried EDIS settings and it operates ok in that mode. Tuner studio seems to show the first input but no second input in the trigger viewer (Not sure if I'm looking at it right).
My settings are below. Any ideas on what I might have done wrong or where I should start trying to fault find.
I've set it as per the MS1 writeup on diyautotune with pullup resistors but sending the 2nd tach signal to JS10 for MS2 input. Have also done the outputs as per Joe Perez's mod.
This is for a 1.8 BP engine. But I wont be seeing the car for another 4 months so this is purely a bench testing game for now.
Tuner studio settings are:
mode: 4g63
offset: 0
skip pulses: 3
Input capture: falling edge
output: going high
number of coils: wasted
spark A output: D14
Jim stim settings are:
2 and 3 on all others off
primary tach jumpered for hall sensor
secondary tach jumper wire to IAC1A
No pullups (I presume not needed because of the ms pullup circuits but I did try the pullup jumpers to no avail)
In tuner studio I can get all the MAT/CLT/TPS etc working. Can't seem to get the tach working.
Seem to have settings correct but no tach reading. If I set input capture to rising edge (which isn't correct anyway) then I do get a crazy erattic jumpy reading on the tach. With falling edge I get no reading at all. Also tried EDIS settings and it operates ok in that mode. Tuner studio seems to show the first input but no second input in the trigger viewer (Not sure if I'm looking at it right).
My settings are below. Any ideas on what I might have done wrong or where I should start trying to fault find.
I've set it as per the MS1 writeup on diyautotune with pullup resistors but sending the 2nd tach signal to JS10 for MS2 input. Have also done the outputs as per Joe Perez's mod.
This is for a 1.8 BP engine. But I wont be seeing the car for another 4 months so this is purely a bench testing game for now.
Tuner studio settings are:
mode: 4g63
offset: 0
skip pulses: 3
Input capture: falling edge
output: going high
number of coils: wasted
spark A output: D14
Jim stim settings are:
2 and 3 on all others off
primary tach jumpered for hall sensor
secondary tach jumper wire to IAC1A
No pullups (I presume not needed because of the ms pullup circuits but I did try the pullup jumpers to no avail)
Last edited by luke2152; 11-07-2013 at 09:56 AM. Reason: simplified the input circuit and still had no luck
#2
Update: Tried switching the primary and secondary signals on the jimstim and can get get both ckp and cmp signals on tuner studio but only one at a time and only on primary channel. So I guess the stim is working ok. Its like the MS2 isn't even receiving anything on the 2nd input circuit.
Is there something I have to so to enable JS10? I'm sure I've been through every menu in tunerstudio and not seen anything needing enabling.
Is there something I have to so to enable JS10? I'm sure I've been through every menu in tunerstudio and not seen anything needing enabling.
Thread
Thread Starter
Forum
Replies
Last Post
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM