Miatas For Sale

Welcome to Miataturbo.net   Members
 
Register Forgot Password?

Welcome to Miata Turbo Forum - Turbo Kitten is watching you test compression.

Reply
 
 
 
 
LinkBack Thread Tools

Old 11-23-2011, 10:56 AM   #1
Default Voltage discrepancy on 12V+ to Megasquirt, is this a problem?  
Junior Member
 
I am: Andy
Join Date: Aug 2009
Location: Lake Jackson, TX
Posts: 120
Feedback: 0 / 0%
Total Props: 1
This probably sounds like a foolish question, but I figure it's better to ask and know than to guess and remain ignorant.

I recently added a voltage gauge to the dashboard on my TunerStudio (paranoia thanks to a defective alternator's untimely demise) and noticed that it reads about 0.5 - 0.75 volts lower than the system voltage when the car is running. Using my multimeter, I determined that the 12v power source (taken from the original power source for the OEM OBD2 ECU) itself is actually lower than the system voltage. I'm not sure if there is some sort of protection built-in to that circuit to prevent accidental voltage spikes from damaging the factory ECU, but my testing with the multimeter definitely shows it to have around 13.5 volts when the rest of the car is running 14.2 volts.

I assume that this discrepancy could throw off some of the sensor calibrations? A lot of the MegaSquirt's control is based on regulated 5v signal though, so I'm not sure if anything is critically affected by this.

I am inclined to find a new power source for the MegaSquirt, but I'm not sure how necessary this is, or even if the OEM power source might be safer somehow?

Other relevant information: 1997 Miata, stock engine, MS1 (pcb3), parallel install with dedicated CLT and IAT sensors and dedicated grounds, Innovate LC-1
jnshk is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 11-23-2011, 11:18 AM   #2
Default  
Boost Czar

 
Braineack's Avatar
 
I am: Scott
Join Date: May 2005
Location: Chantilly, VA
Posts: 49,436
Feedback: 54 / 100%
Total Props: 480
Measure the voltage at the injectors, the MS should match this. If not, calibrate as needed.
Braineack is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 11-23-2011, 11:59 AM   #3
Default  
Junior Member
 
I am: Andy
Join Date: Aug 2009
Location: Lake Jackson, TX
Posts: 120
Feedback: 0 / 0%
Total Props: 1
OK, I think that answers my question then. The 12v power for the OBD2 (and MS at present) reads at ~13.6v with the engine running. The 12v power for the injectors reads at the same voltage. So my power supply is good. Thanks!

Out of curiosity though, is this normal for these cars? I've never heard anyone mention before that the power supply to the ECU is actually slightly reduced from that of the rest of the car? Is is supposed to be that way, or am I getting some unintended voltage drop at the fuse or relay?
jnshk is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 11-23-2011, 12:26 PM   #4
Default  
Boost Czar

 
Braineack's Avatar
 
I am: Scott
Join Date: May 2005
Location: Chantilly, VA
Posts: 49,436
Feedback: 54 / 100%
Total Props: 480
just a voltage drop, but you want the MS to read what the injectors see, since it does voltage based corrections to them.
Braineack is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiTweet this Post!
Reply With Quote
Old 11-23-2011, 12:26 PM
 
 
 
Reply


Tags
megasquirt, parallel, parallel harness, voltage, wiring

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Intermittent disconnection problem Megasquirt 2. mauro miata MEGAsquirt 4 09-26-2011 12:04 PM
Voltage Drop with A/C (Now voltage spike while driving) Braineack General Miata Chat 60 04-29-2011 05:39 PM
AEM Wideband / Megasquirt Problem D.dutton9512 MEGAsquirt 11 03-23-2010 04:52 PM
Small Megasquirt Problem drbogg MEGAsquirt 5 06-13-2009 07:47 PM
Megasquirt PNP Launch control problem, need help! Cody Strife MEGAsquirt 6 06-09-2008 12:09 AM