1.8 VHT High Heat Wrinkle Red Valve Cover
#1
Newb
Thread Starter
iTrader: (7)
Join Date: Jan 2009
Location: Long Beach, CA
Posts: 40
Total Cats: 0
1.8 VHT High Heat Wrinkle Red Valve Cover
:SALE PENDING:
Valve cover is off a 1.8 Protege.
- 3 Coats of VHT High Heat Wrinkle Red fully dried and cured under 200F Oven degree for about 20 minutes.
- Raised Letters Polished
- Back Hole Plugged tight
- Tapped side for vent
- Will include everything as pictured here along with a good condition gasket and the center plug wire holder brackets.
Have not been put of to use. All the work is done, you just need to buy it and put it on.
Price Shipped and Paypal'd is $100 Flat.
Local SoCal Long Beach area pickup is $90 Flat.
Finished engine look would be similar to below with Cam Gears exposed.
Valve cover is off a 1.8 Protege.
- 3 Coats of VHT High Heat Wrinkle Red fully dried and cured under 200F Oven degree for about 20 minutes.
- Raised Letters Polished
- Back Hole Plugged tight
- Tapped side for vent
- Will include everything as pictured here along with a good condition gasket and the center plug wire holder brackets.
Have not been put of to use. All the work is done, you just need to buy it and put it on.
Price Shipped and Paypal'd is $100 Flat.
Local SoCal Long Beach area pickup is $90 Flat.
Finished engine look would be similar to below with Cam Gears exposed.
Last edited by Pharo_X; 11-23-2009 at 12:58 PM. Reason: Added photos
#4
Newb
Thread Starter
iTrader: (7)
Join Date: Jan 2009
Location: Long Beach, CA
Posts: 40
Total Cats: 0
Not sure what I was thinking of, prepping it up thinking it would fit my 1.6 "BIG FAIL".
Maybe someone else can make better use of it.
"Zoomin" - it does have enough clearance for the back coil area if that's what you meant.
Thanks for looking.
Shoot me some PM if anyone's interested.
Maybe someone else can make better use of it.
"Zoomin" - it does have enough clearance for the back coil area if that's what you meant.
Thanks for looking.
Shoot me some PM if anyone's interested.
#7
Newb
Thread Starter
iTrader: (7)
Join Date: Jan 2009
Location: Long Beach, CA
Posts: 40
Total Cats: 0
Trade is ok, but not sure how we can go forth with such, unless it's a local trade.
Looking for wideband 02 sensor/gauge, 1.6 valve cover with raised letter, aftermarket Cam Gears, interior dress up, rear strut brace...
I can always add on my end.
Looking for wideband 02 sensor/gauge, 1.6 valve cover with raised letter, aftermarket Cam Gears, interior dress up, rear strut brace...
I can always add on my end.
#9
Newb
Thread Starter
iTrader: (7)
Join Date: Jan 2009
Location: Long Beach, CA
Posts: 40
Total Cats: 0
It should fit the 1.8 fine.
It DOES NOT fit the 1.6 because of the back loop (as illustrated below). The 1.6 is on passenger side, and 1.8 is on driver side as the valve cover I'm selling.
Hope that clears it for anyone else trying to do the Protege valve cover.
It DOES NOT fit the 1.6 because of the back loop (as illustrated below). The 1.6 is on passenger side, and 1.8 is on driver side as the valve cover I'm selling.
Hope that clears it for anyone else trying to do the Protege valve cover.
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
russian
Miata parts for sale/trade
6
10-08-2015 03:01 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM