Chapman

iTrader: (2)

Selling this from my 95 with AC, Cruise Control and Power Steering. PNP for 94/95.
Downpipe was repaired(when I bought it there was a pin sized hole and the metal looked thin) and doesn't look the prettiest but is fully functional.

I was unlucky and after using this on my miata for about a month (this car isn't my DD and I probably only drove it 10-15 times with the turbo) I was pulled over for no front plate and given a state ref ticket for the turbo (just before I received my carb sticker). I had to remove the turbo system and go back to na.

This kit is everything u need to run up to about 220whp depending on your tune. You will need to buy new studs and nuts for the connections to the turbo (mani-turbo-DP). I will include the hoses I used for coolant feed/return.

This thing spooled instantly for me. It was unreal.
Garrett's GT2554Clocked for IC(3000 miles on turbo)
Begi's/FM exhaust manifold (No EGR but I will include the block off plate)
FM/Begi Downpipe(older style)
MSPNP for 95, road tuned at about 6psi(GM boost control and IAT for MAF Delete)
440 injectors(pnp with MS), cleaned before I used them(need a set of gaskets which should always be replaced when removed anyway)
Enthuza Budget Turbo Racer 2.5" cat-back
SS oil feed/Oil drain(for the oil pan just drill hole, screw fitting in, and JB weld it to the pan for a perfect seal)
Innovate LC-1 controller and sensor with all wiring
FMIC -fit with trimming of the undertray and removal of air splitter/diverter thing. I used a bit of ABS sheet I had. The hotside is a silicone Flyin' Miata pipe, coldside is Bell's piece off of the intake mani down to 2.5" pipes and couplers Forge BOV.
Intake is a little ghetto but works.(silicone tube with VC breather tube hole and a filter on the end. very easy to fab your own if you want)
Begi's Turbo Heatsheild(never used)

Looking to get $2200 and I would obviously prefer to sell locally(southern california-ish). I guess I will ship but at the buyers expense. Not parting this unless there is a buyer for all parts.
There are many compatible parts with this if upgrades are wanted in the future(Intake, DP, Mani, etc.). It's basically a FM or Begi kit with some homebrew touches.

BTW Disclaimer I do have a BEGI CARB sticker also but should not be used unless the kit is used in accordance to their rules(EGR drilled and fitted to mani, Stock injectors, Bandaids or piggyback) I have bandaids for sale(minus walbro) and I will post them in another thread, as well as a 6 puck sprung ACT clutch disk.(PS also posting this on another forum as ilovecurves)

Now for pics...

Chapman

iTrader: (2)

I haven't snapped a pic of the cat-back yet but I can if needed.

gt2554

Downpipe(bottom half included obviously but not pictured)

Exhaust Manifold(looks like **** but clean up is easy with BBQ paint + Heatshield covering it.)

MSPNP with injectors(440's are included and 460's pictured too)

Intercooler, Intake, BOV setup

Oil feed/drain, coolant lines, magnacore wires,

Heat shield


Random pics of IC fitting

aznDragonX

iTrader: (5)

want to sell SS oil feed/Oil drain lines and FMIC setup? if so..how much?

UrbanSoot

iTrader: (24)

i can vouch for this kit since i helped install it

gospeed81

iTrader: (51)

I didn't know you'd ever installed a turbo kit...


OP: Good looking kit. Good luck with sell.

chriscar

iTrader: (24)

Interested in the exhaust if you wind up parting out the kit.

C

Turbo_4

iTrader: (6)

interested in the injectors if you end up parting it out.

ajbalmat

iTrader: (2)

interested in the manifold if you part out.

UrbanSoot

iTrader: (24)

part it out dude!

Rt77

Interested in MSPNP, Innovate LC-1 and Heatshield!

Chapman

iTrader: (2)

I may be parting this out guys. Lemme put some #'s together and I'll pm u guys. If you want dibs on stuff the thread is where to do it(don't pm). That way it's obvious to everyone who calls for what.

Gimme a day or so to put this together.

Also, Sorry for the Bandwidth Fail guys

Rt77

paycheck is in, so is it still for sale?

I'm still interested in MSPNP, Innovate LC-1, Heatshield and ic (piping)

cheerz,

Rt

rider384

iTrader: (3)

If parting it out, how much for the manifold?

evomiata

2nd dibs on exhaust, pm me price pelase thanks

Chapman

iTrader: (2)

ok guys pics are working again... New plans. I'm keeping the MSPNP and LC-1

$1850 for the rest of this stuff plus shipping OBO. I really want to sell it together. If you want to make an offer for something PM me.

I wouldn't mind selling the exhaust by itself, but I would really prefer to sell turbo, mani, dp, and ic together because they all work together.


Plus New ACT 6-puck sprung clutch disc for sale $90 shipped***SOLD***

Bipes unit $130 shipped
FPR $30 +shipping
O2 clamp $55 shipped

rider384

iTrader: (3)

Hi, if you decide to part it how much for:
Bell's piece off of the intake mani down to 2.5" pipes

Chapman

iTrader: (2)

I'm keeping the Intercooler piping with intercooler for sure. I really don't want to break the kit down to individual pipes. sorry.

Chapman

iTrader: (2)

I want to change the price to $1700. I want this stuff gone. It's a great deal for this stuff. I paid a lot more for this stuff. For everything listed in my first post except for the MSPNP and the lc-1.

Spins

iTrader: (10)

Do u still have the bipes, fpr and 02 clamp for sale? If so is the fpr a Begi? Any pics? U can email me at mshorty6686@aol.com or pm me here.
Sorry i'm unable to PM since I don't have enough posts.
I perfer to search for my info instead of posting retorical questions.