Complete 1.6 Turbo Setup
11-30-2012, 12:45 PM
#1
Junior Member
Thread Starter
iTrader: (6)
Join Date: Apr 2012
Location: Washington
Posts: 163
Total Cats: 0
Complete 1.6 Turbo Setup
Up for sale is the turbo kit that I purchased from a member on MT (underdog). It was on his car for about 2000 miles and I never got around to installing it (decided not to do turbo). I am selling this because I plan on selling the car in the spring. You can see all of the details, photos, dyno results, etc. in his build thread or you can see the various stages broken down by date/topic on his website.
Includes the following items:
-Godspeed/Ebay T3 turbocharger- 50 trim, .48 A/R with Earl's -3AN oil feed fitting and Ebay 5/8" oil drain fitting
-Ebay cast iron turbo manifold. Modified with relief cuts and a Tial v-band external wastegate flange
-Tial 38mm MVS v-band external wastegate
-Steel T3 inlet gasket
-V-band wastegate atmosphere dump tube
-ATP Turbo 5 bolt T3 turbo exhaust flange to 2.5" v-band adapter. Includes bolts and steel gasket
-2.5" v-band downpipe with a slip fit exit and heat wrapped. Includes O2 sensor fitting. Pipe is welded steel mandrel bends
-Autogauge fuel pressure gauge and fittings for installing inline with stock Miata fuel line
-CXRacing/Ebay Intercooler - 28x7x2.5 with 2.5" inlets and outlets
-2" hot side intercooler piping with silicone connectors/reducers and clamps. Pipes are welded steel mandrel bends
-2.5" cold side intercooler piping with silicone/rubber connectors and clamps. Flanged for a Tial 50mm blowoff valve
-Tial 50mm blowoff valve
-CoolingMist alcohol injection nozzle mounted in cold side pipe. The nozzle part was stuck, so I left it in the pipe.
-Ebay Slim radiator fan- allows easy installation of hot side intercooler piping
-Rubber turbo intake elbow with K&N Filter & rubber line with an inline filter for valve cover venting
-Paragon Performance M10 x 1.5 to -3AN oil feed fitting
-Earl's 36" -3AN oil feed line
-NAPA 5/8" Oil pan turbo oil drain fitting
-Drill bit and tap for installing oil pan drain fitting
-ATP Turbo high temp silicone 5/8" oil drain hose
-Extreme Motorsports Manual Boost Controller (old, but works great)
A couple notes:
-You will need to purchase one 2.5" v-band clamp. The one that connects to the downpipe broke when I removed it. You can find them on Ebay, just use some high temp anti-seize on the bolt threads when installing.
-The cold side pipe will need to be extended a few inches at its exit in order to mate up to the stock Miata throttle body. This may be accomplished with a silicone connector, but one way or another it will need done. Not a big deal, if you choose to have it welded on any exhaust or fab shop could do this quickly.
If you have any questions feel free to ask. I will do my best to answer.
Price is $1200 plus shipping or $1100 picked up near Bellingham, WA.
Includes the following items:
-Godspeed/Ebay T3 turbocharger- 50 trim, .48 A/R with Earl's -3AN oil feed fitting and Ebay 5/8" oil drain fitting
-Ebay cast iron turbo manifold. Modified with relief cuts and a Tial v-band external wastegate flange
-Tial 38mm MVS v-band external wastegate
-Steel T3 inlet gasket
-V-band wastegate atmosphere dump tube
-ATP Turbo 5 bolt T3 turbo exhaust flange to 2.5" v-band adapter. Includes bolts and steel gasket
-2.5" v-band downpipe with a slip fit exit and heat wrapped. Includes O2 sensor fitting. Pipe is welded steel mandrel bends
-Autogauge fuel pressure gauge and fittings for installing inline with stock Miata fuel line
-CXRacing/Ebay Intercooler - 28x7x2.5 with 2.5" inlets and outlets
-2" hot side intercooler piping with silicone connectors/reducers and clamps. Pipes are welded steel mandrel bends
-2.5" cold side intercooler piping with silicone/rubber connectors and clamps. Flanged for a Tial 50mm blowoff valve
-Tial 50mm blowoff valve
-CoolingMist alcohol injection nozzle mounted in cold side pipe. The nozzle part was stuck, so I left it in the pipe.
-Ebay Slim radiator fan- allows easy installation of hot side intercooler piping
-Rubber turbo intake elbow with K&N Filter & rubber line with an inline filter for valve cover venting
-Paragon Performance M10 x 1.5 to -3AN oil feed fitting
-Earl's 36" -3AN oil feed line
-NAPA 5/8" Oil pan turbo oil drain fitting
-Drill bit and tap for installing oil pan drain fitting
-ATP Turbo high temp silicone 5/8" oil drain hose
-Extreme Motorsports Manual Boost Controller (old, but works great)
A couple notes:
-You will need to purchase one 2.5" v-band clamp. The one that connects to the downpipe broke when I removed it. You can find them on Ebay, just use some high temp anti-seize on the bolt threads when installing.
-The cold side pipe will need to be extended a few inches at its exit in order to mate up to the stock Miata throttle body. This may be accomplished with a silicone connector, but one way or another it will need done. Not a big deal, if you choose to have it welded on any exhaust or fab shop could do this quickly.
If you have any questions feel free to ask. I will do my best to answer.
Price is $1200 plus shipping or $1100 picked up near Bellingham, WA.
0
12-01-2012, 10:01 AM
#5
Newb
Join Date: Aug 2012
Posts: 1
Total Cats: 0
Hi , i am intrested , would it be possible to ship to the Netherlands?
Regards.
Johan Draijer , you can email me at johandraijer(at)hotmail.com
Regards.
Johan Draijer , you can email me at johandraijer(at)hotmail.com
0
12-02-2012, 06:28 PM
#8
Newb
Join Date: Nov 2012
Location: surrey
Posts: 3
Total Cats: 0
Txt me 604 839 9032, can probably pick up soon if everything goes well
Last edited by FrontYardigans; 12-02-2012 at 07:40 PM.
0
12-04-2012, 01:39 PM
#10
Senior Member
Join Date: Aug 2009
Location: MONROE CT
Posts: 1,102
Total Cats: 3
Price on the tial wastegate?
0
12-07-2012, 10:27 PM
#13
Newb
Join Date: Dec 2012
Location: KY
Posts: 25
Total Cats: 0
sale still pending?
0
Thread
Thread Starter
Forum
Replies
Last Post
