Turbo track car part out, lots of good parts in here!
08-08-2012, 09:28 PM
#1
Junior Member
Thread Starter
iTrader: (14)
Join Date: Jan 2010
Location: Buford GA
Posts: 212
Total Cats: 1
Turbo track car part out, lots of good parts in here!
I am going to start parting out my turbo track car so I can move on to another project.
Below is a list of some of the items that are on the block, I will add more when they come up since I'm sure I have forgotten a few things.
The car is currently still in one piece so please be patient with timeframes on certain parts. I will be up front about when I can get to certain pieces of the car. Please check my feedback and feel free to contact anybody I have done business with here, I am a stand up guy.
Prices are OBO they do not include shipping. Please add 3.5% if you wish to use Paypal.
My zip is 30518 if you want to get an idea of what shipping would cost you.
95 1.8 $2200
Less than 500 miles since the build. The machine work and assembly was done by NOMSG and Balanced Performance did the tune once it was completed. The motor was broken in properly with 30 wt oil and no boost. Here is a short list of the specs and parts.
-8.8:1 compression ratio
-ARP head, main cap, and connecting rod bolts.
-M-Tuned rods
-Clevite bearings
-Cylinder head and Manifold are port matched
-Coolant reroute
-Oil pan has 10an fitting welded on for the turbo's oil return
-I have a 99 head and manifold that could be thrown in as a sweetener.
Turbo kit $2200
-Begi manifold and downpipe
-Trackspeed Engineering Inconel stud kit
-Garrett GT2871R
-stainless braided oil lines
-550cc Denso RX-7 injectors
-Turbosmart BOV
-AEM wideband
-Intercooler
-Hot and cold side pipes with all silicone connectors and t-bolt clamps
Rolling chassis with roll cage $1500
This would make a great start for a chump or Lemons car, The cage was built using NASA guidelines for a 2501-3000lb car.
DIYPNP 90-93 $400
Trackspeed Engineering Toyota Cops (wired for a 1.8 swapped into a 90-93) Sold
Walbro 190HP fuel pump $65
3in Enthuza Dual exhaust Sold
ACT Extreme 6-puck clutch and pressure plate for the 1.6 (can be used on the 1.8 with a 1.6 flywheel) $250
99 5-speed $250
4.1 Torsen swap w/ axles and driveshaft included (I currently have two complete swaps) $500 ea
Tein Flex w/10k front and 6k rear springs Pending
Racing Beat tubular front sway bar and adjustable rear $old
Racing beat adjustable sway bar end links $80
Racing beat sway bar brace $50
FM Cannon brace Sold
1.8 brakes with nearly new Hawk DTC-60 pads $300
Corbeau Forza seat (some wear) $150
(2) Sparco 5-point cam lock harnesses in fantastic shape, dates are expired $100 / set
Momo Monte Carlo steering wheel Sold
NRG quick release Gen 2 w/ short hub Sold
Lexan pop out vent windows (fits 90-05) Sold
Convex mirror $30
Below is a list of some of the items that are on the block, I will add more when they come up since I'm sure I have forgotten a few things.
The car is currently still in one piece so please be patient with timeframes on certain parts. I will be up front about when I can get to certain pieces of the car. Please check my feedback and feel free to contact anybody I have done business with here, I am a stand up guy.
Prices are OBO they do not include shipping. Please add 3.5% if you wish to use Paypal.
My zip is 30518 if you want to get an idea of what shipping would cost you.
95 1.8 $2200
Less than 500 miles since the build. The machine work and assembly was done by NOMSG and Balanced Performance did the tune once it was completed. The motor was broken in properly with 30 wt oil and no boost. Here is a short list of the specs and parts.
-8.8:1 compression ratio
-ARP head, main cap, and connecting rod bolts.
-M-Tuned rods
-Clevite bearings
-Cylinder head and Manifold are port matched
-Coolant reroute
-Oil pan has 10an fitting welded on for the turbo's oil return
-I have a 99 head and manifold that could be thrown in as a sweetener.
Turbo kit $2200
-Begi manifold and downpipe
-Trackspeed Engineering Inconel stud kit
-Garrett GT2871R
-stainless braided oil lines
-550cc Denso RX-7 injectors
-Turbosmart BOV
-AEM wideband
-Intercooler
-Hot and cold side pipes with all silicone connectors and t-bolt clamps
Rolling chassis with roll cage $1500
This would make a great start for a chump or Lemons car, The cage was built using NASA guidelines for a 2501-3000lb car.
DIYPNP 90-93 $400
Trackspeed Engineering Toyota Cops (wired for a 1.8 swapped into a 90-93) Sold
Walbro 190HP fuel pump $65
3in Enthuza Dual exhaust Sold
ACT Extreme 6-puck clutch and pressure plate for the 1.6 (can be used on the 1.8 with a 1.6 flywheel) $250
99 5-speed $250
4.1 Torsen swap w/ axles and driveshaft included (I currently have two complete swaps) $500 ea
Tein Flex w/10k front and 6k rear springs Pending
Racing Beat tubular front sway bar and adjustable rear $old
Racing beat adjustable sway bar end links $80
Racing beat sway bar brace $50
FM Cannon brace Sold
1.8 brakes with nearly new Hawk DTC-60 pads $300
Corbeau Forza seat (some wear) $150
(2) Sparco 5-point cam lock harnesses in fantastic shape, dates are expired $100 / set
Momo Monte Carlo steering wheel Sold
NRG quick release Gen 2 w/ short hub Sold
Lexan pop out vent windows (fits 90-05) Sold
Convex mirror $30
Last edited by VitaminD; 08-21-2012 at 09:53 AM. Reason: forgot some ----
Reply
0
0
))
