Injectors VTPS , Toyota COPS
#1
Senior Member
Thread Starter
iTrader: (12)
Join Date: May 2008
Location: Roselle, Illinois
Posts: 849
Total Cats: -34
Injectors VTPS , Toyota COPS
clutch sold, new stuff
Veriable throttle posisiotn sensors (4 wire)
$28 shipped for each sensor with no pigtail (forgot to grab them!)
$50 Miata throttle body with a variable tps sensor w/ pig tail, iac installed
Precision 785 /75lb injectors set of 4, with clips. Low impedance, comes with clips and a resistor pack so they can be used in High impedance applications (standalone computer) $175.00 shipped
the other set is as well 785cc/75lb low impedance Deplhi (same as Precision) comes with clips as well $150.00 shipped
i have not personally ran these injectors but i did ohm them out to make sure there where no duds, they ohmed at 2.4 across all 8. I would suggest sending them out for cleaning due to i dont know the history.
Reason for selling is want to run e85 and im in the market for 1000cc, i will trade plus cash on my end if you have a set
ICPKORN23@aim.com
Veriable throttle posisiotn sensors (4 wire)
$28 shipped for each sensor with no pigtail (forgot to grab them!)
$50 Miata throttle body with a variable tps sensor w/ pig tail, iac installed
Precision 785 /75lb injectors set of 4, with clips. Low impedance, comes with clips and a resistor pack so they can be used in High impedance applications (standalone computer) $175.00 shipped
the other set is as well 785cc/75lb low impedance Deplhi (same as Precision) comes with clips as well $150.00 shipped
i have not personally ran these injectors but i did ohm them out to make sure there where no duds, they ohmed at 2.4 across all 8. I would suggest sending them out for cleaning due to i dont know the history.
Reason for selling is want to run e85 and im in the market for 1000cc, i will trade plus cash on my end if you have a set
ICPKORN23@aim.com
#2
Senior Member
Thread Starter
iTrader: (12)
Join Date: May 2008
Location: Roselle, Illinois
Posts: 849
Total Cats: -34
I have a spare set of Toyota coil over plugs that will fit a b6/ bp. You will need a standalone computer to control these. The miata guys have been running these coil on plugs with great success! they have built in ignitors. Comes with a harness. I will be running these with my AEM EMS.
$85.00 shipped
here is the write up on the wiring for miata use.
https://www.miataturbo.net/useful-sav...writeup-12704/
$85.00 shipped
here is the write up on the wiring for miata use.
https://www.miataturbo.net/useful-sav...writeup-12704/
#5
Senior Member
Thread Starter
iTrader: (12)
Join Date: May 2008
Location: Roselle, Illinois
Posts: 849
Total Cats: -34
i believe the wiring dont matter. Check the link i posted with the write up. If your doing 1.6 i think you can power them up through the ignitor box, or 1.8 you just splice them right into the old coil harness.
https://www.miataturbo.net/useful-sa...writeup-12704/
https://www.miataturbo.net/useful-sa...writeup-12704/
#7
Senior Member
Thread Starter
iTrader: (12)
Join Date: May 2008
Location: Roselle, Illinois
Posts: 849
Total Cats: -34
found the original sellers post, he was running them on a bp
https://www.miataturbo.net/miata-par...05/#post911747
https://www.miataturbo.net/miata-par...05/#post911747
Last edited by Hot_Wheels; 09-06-2012 at 01:37 PM.
#10
I have a spare set of Toyota coil over plugs that will fit a b6/ bp. You will need a standalone computer to control these. The miata guys have been running these coil on plugs with great success! they have built in ignitors. Comes with a harness. I will be running these with my AEM EMS.
$85.00 shipped
here is the write up on the wiring for miata use.
https://www.miataturbo.net/useful-sav...writeup-12704/
$85.00 shipped
here is the write up on the wiring for miata use.
https://www.miataturbo.net/useful-sav...writeup-12704/
And also can you post P/N of COPs? Which one from below:
90080-19015
90919-02239
90080-19023
90919-02234
#11
Senior Member
Thread Starter
iTrader: (12)
Join Date: May 2008
Location: Roselle, Illinois
Posts: 849
Total Cats: -34
im having someone make me a custom harness due to i want to run a AEM EMS in my ford festiva. The guy doing the wiring said he is just going make me a new harness and it will all be integrated with the engine harness he is making.
coils are 90919-02239
coils are 90919-02239