MSPNP PR0 need help wiring it o_O
#1
MSPNP PR0 need help wiring it o_O
Hi Community,
I want to build a 05 vvt Miata turbo. I bought a MSPNP PRO used from ebay.com and downloaded the Manual. I was searching for a Pinout diagramm but sadly i have not found it for the MSPNP PRO :(. The manual only got the rear option connector description in it. I want to know where to wire the Spartan2 and the IAT-Sensor i bought. I am new to MS and hope for your help.
Beside this: I tested the MS with everything else standard: I noticed that the engine starts very late and is reving high and dies when i try to accelerate. The engine run for just 30 sec. is this behavior normal?
Greets from Germany
I want to build a 05 vvt Miata turbo. I bought a MSPNP PRO used from ebay.com and downloaded the Manual. I was searching for a Pinout diagramm but sadly i have not found it for the MSPNP PRO :(. The manual only got the rear option connector description in it. I want to know where to wire the Spartan2 and the IAT-Sensor i bought. I am new to MS and hope for your help.
Beside this: I tested the MS with everything else standard: I noticed that the engine starts very late and is reving high and dies when i try to accelerate. The engine run for just 30 sec. is this behavior normal?
Greets from Germany
#2
Hi Community,
I want to build a 05 vvt Miata turbo. I bought a MSPNP PRO used from ebay.com and downloaded the Manual. I was searching for a Pinout diagramm but sadly i have not found it for the MSPNP PRO :(. The manual only got the rear option connector description in it. I want to know where to wire the Spartan2 and the IAT-Sensor i bought. I am new to MS and hope for your help.
Beside this: I tested the MS with everything else standard: I noticed that the engine starts very late and is reving high and dies when i try to accelerate. The engine run for just 30 sec. is this behavior normal?
Greets from Germany
I want to build a 05 vvt Miata turbo. I bought a MSPNP PRO used from ebay.com and downloaded the Manual. I was searching for a Pinout diagramm but sadly i have not found it for the MSPNP PRO :(. The manual only got the rear option connector description in it. I want to know where to wire the Spartan2 and the IAT-Sensor i bought. I am new to MS and hope for your help.
Beside this: I tested the MS with everything else standard: I noticed that the engine starts very late and is reving high and dies when i try to accelerate. The engine run for just 30 sec. is this behavior normal?
Greets from Germany
#4
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
MegaSquirtPNP by DIYAutoTune.com
although after reading through this, it's still completely unclear which pin on the rear connector is actually used for wbo2 in...
I think 18psi had this same problem...surprised they haven't updated the documentation since.
03-17-2015, 03:34 PM
one hell of a long time to update them...
but the answer is:
although after reading through this, it's still completely unclear which pin on the rear connector is actually used for wbo2 in...
I think 18psi had this same problem...surprised they haven't updated the documentation since.
03-17-2015, 03:34 PM
Just a minor oversight and we'll get it fixed now that you have brought it to our attention.
but the answer is:
Update - you may use any of the extra analog inputs; just change the O2 input port in the software. This was done so you don't have to unplug any of the stock O2s.
#11
Do you want to scan your serial ports automatically? (y/n default y)
Trying: COM5 ..TX: 51
Waiting...
Waiting...
TX: 0d
Waiting...
Waiting...
Trying: COM256 ..
WARNING!!!
No valid ports or ECUs found. Cannot load firmware without communications.
Common problems:
- Something is hogging the serial port.
e.g. TunerStudio, modem or mobile phone cable software.
Be sure to close/exit those applications.
- USB-serial cable on high COM port number, use Device Manager to re-assign
it to say COM1.
- ECU not powered up, be sure there is fused power applied. Use a mains
adapter or vehicle battery. PP9 batteries are too feeble.
- Serial cable not connected correctly
- Software driver problems
Check the above. Do you want to try probing again? (y/n default = y)
NEW CHECK (2)
Trying: COM1 ..#Opening comm port COM1
COM1 does not exist.
couldn't open port
#Comm port already closed
Trying: COM2 ..#Opening comm port COM2
COM2 does not exist.
couldn't open port
#Comm port already closed
Trying: COM3 ..#Opening comm port COM3
COM3 does not exist.
couldn't open port
#Comm port already closed
Trying: COM4 ..#Opening comm port COM4
COM4 does not exist.
couldn't open port
#Comm port already closed
Trying: COM5 ..#Opening comm port COM5
TX: 51
Waiting...
Waiting...
TX: 0d
Waiting...
Waiting...
#Closing comm port
Trying: COM6 ..#Opening comm port COM6
COM6 does not exist.
couldn't open port
#Comm port already closed
Trying: COM7 ..#Opening comm port COM7
COM7 does not exist.
couldn't open port
#Comm port already closed
Trying: COM8 ..#Opening comm port COM8
COM8 does not exist.
couldn't open port
#Comm port already closed
Trying: COM9 ..#Opening comm port COM9
COM9 does not exist.
couldn't open port
#Comm port already closed
Trying: COM10 ..#Opening comm port COM10
COM10 does not exist.
couldn't open port
#Comm port already closed
Trying: COM11 ..#Opening comm port COM11
COM11 does not exist.
couldn't open port
#Comm port already closed
Trying: COM12 ..#Opening comm port COM12
COM12 does not exist.
couldn't open port
#Comm port already closed
Trying: COM13 ..#Opening comm port COM13
COM13 does not exist.
couldn't open port
#Comm port already closed
Trying: COM14 ..#Opening comm port COM14
COM14 does not exist.
couldn't open port
#Comm port already closed
Trying: COM15 ..#Opening comm port COM15
COM15 does not exist.
couldn't open port
#Comm port already closed
Trying: COM16 ..#Opening comm port COM16
COM16 does not exist.
couldn't open port
#Comm port already closed
Trying: COM17 ..#Opening comm port COM17
COM17 does not exist.
couldn't open port
#Comm port already closed
Trying: COM18 ..#Opening comm port COM18
COM18 does not exist.
couldn't open port
#Comm port already closed
Trying: COM19 ..#Opening comm port COM19
COM19 does not exist.
couldn't open port
WARNING!!!
No valid ports or ECUs found. Cannot load firmware without communications.
Common problems:
- Something is hogging the serial port.
e.g. TunerStudio, modem or mobile phone cable software.
Be sure to close/exit those applications.
- USB-serial cable on high COM port number, use Device Manager to re-assign
it to say COM1.
- ECU not powered up, be sure there is fused power applied. Use a mains
adapter or vehicle battery. PP9 batteries are too feeble.
- Serial cable not connected correctly
- Software driver problems
Check the above. Do you want to try probing again? (y/n default = y)
NEW CHECK (3)
MegaSquirt-3 Firmware Loader 3.45 2017-01-16
---------------------------------------------------------------------------
This firmware loader is only licensed for loading Megasquirt firmware onto
official Megasquirt hardware.
Using Megasquirt firmware on un-approved devices is in breach of copyright.
Visit Megasquirt EFI - Fuel injection and Ignition Control ECU to check the validity of your hardware.
-----------------------------------------------------------------------------
Remove the fuse powering your ignition coils.
(Spark outputs may be undefined until you re-load your settings.)
Press enter to continue...
Ensure that your Megasquirt/Microsquirt/ECU is
-connected to your computer
-has fused 12V power connected.
Press enter to continue...
Ensure that no tuning software is running.
Be sure to Quit the software, not just minimise it..
Press enter to continue...
Debug message Level:
1: Normal
2: More detail
3: + serial comms
4: + the s19 file as parsed
Selection (default: 1): 3
Do you want to scan your serial ports automatically? (y/n default y)
Trying: COM1 ..#Opening comm port COM1
(\\.\COM1)
COM1 does not exist.
couldn't open port
#Comm port already closed
Trying: COM2 ..#Opening comm port COM2
(\\.\COM2)
COM2 does not exist.
couldn't open port
#Comm port already closed
Trying: COM3 ..#Opening comm port COM3
(\\.\COM3)
COM3 does not exist.
couldn't open port
#Comm port already closed
Trying: COM4 ..#Opening comm port COM4
(\\.\COM4)
COM4 does not exist.
couldn't open port
#Comm port already closed
Trying: COM5 ..#Opening comm port COM5
(\\.\COM5)
TX: 51
Waiting...
Waiting...
Sent Q and got 0 bytes back.
TX: 0d
Waiting...
Waiting...
Sent 0d and got 0 bytes back #Closing comm port
Trying: COM6 ..#Opening comm port COM6
(\\.\COM6)
COM6 does not exist.
couldn't open port
#Comm port already closed
Trying: COM7 ..#Opening comm port COM7
(\\.\COM7)
COM7 does not exist.
couldn't open port
#Comm port already closed
Trying: COM8 ..#Opening comm port COM8
(\\.\COM8)
#Comm port already closed
WARNING!!!
No valid ports or ECUs found. Cannot load firmware without communications.
Common problems:
- Something is hogging the serial port.
e.g. TunerStudio, modem or mobile phone cable software.
Be sure to close/exit those applications.
- USB-serial cable on high COM port number, use Device Manager to re-assign
it to say COM1.
- ECU not powered up, be sure there is fused power applied. Use a mains
adapter or vehicle battery. PP9 batteries are too feeble.
- Serial cable not connected correctly
- Software driver problems
Check the above. Do you want to try probing again? (y/n default = y)
Trying: COM5 ..TX: 51
Waiting...
Waiting...
TX: 0d
Waiting...
Waiting...
Trying: COM256 ..
WARNING!!!
No valid ports or ECUs found. Cannot load firmware without communications.
Common problems:
- Something is hogging the serial port.
e.g. TunerStudio, modem or mobile phone cable software.
Be sure to close/exit those applications.
- USB-serial cable on high COM port number, use Device Manager to re-assign
it to say COM1.
- ECU not powered up, be sure there is fused power applied. Use a mains
adapter or vehicle battery. PP9 batteries are too feeble.
- Serial cable not connected correctly
- Software driver problems
Check the above. Do you want to try probing again? (y/n default = y)
NEW CHECK (2)
Trying: COM1 ..#Opening comm port COM1
COM1 does not exist.
couldn't open port
#Comm port already closed
Trying: COM2 ..#Opening comm port COM2
COM2 does not exist.
couldn't open port
#Comm port already closed
Trying: COM3 ..#Opening comm port COM3
COM3 does not exist.
couldn't open port
#Comm port already closed
Trying: COM4 ..#Opening comm port COM4
COM4 does not exist.
couldn't open port
#Comm port already closed
Trying: COM5 ..#Opening comm port COM5
TX: 51
Waiting...
Waiting...
TX: 0d
Waiting...
Waiting...
#Closing comm port
Trying: COM6 ..#Opening comm port COM6
COM6 does not exist.
couldn't open port
#Comm port already closed
Trying: COM7 ..#Opening comm port COM7
COM7 does not exist.
couldn't open port
#Comm port already closed
Trying: COM8 ..#Opening comm port COM8
COM8 does not exist.
couldn't open port
#Comm port already closed
Trying: COM9 ..#Opening comm port COM9
COM9 does not exist.
couldn't open port
#Comm port already closed
Trying: COM10 ..#Opening comm port COM10
COM10 does not exist.
couldn't open port
#Comm port already closed
Trying: COM11 ..#Opening comm port COM11
COM11 does not exist.
couldn't open port
#Comm port already closed
Trying: COM12 ..#Opening comm port COM12
COM12 does not exist.
couldn't open port
#Comm port already closed
Trying: COM13 ..#Opening comm port COM13
COM13 does not exist.
couldn't open port
#Comm port already closed
Trying: COM14 ..#Opening comm port COM14
COM14 does not exist.
couldn't open port
#Comm port already closed
Trying: COM15 ..#Opening comm port COM15
COM15 does not exist.
couldn't open port
#Comm port already closed
Trying: COM16 ..#Opening comm port COM16
COM16 does not exist.
couldn't open port
#Comm port already closed
Trying: COM17 ..#Opening comm port COM17
COM17 does not exist.
couldn't open port
#Comm port already closed
Trying: COM18 ..#Opening comm port COM18
COM18 does not exist.
couldn't open port
#Comm port already closed
Trying: COM19 ..#Opening comm port COM19
COM19 does not exist.
couldn't open port
WARNING!!!
No valid ports or ECUs found. Cannot load firmware without communications.
Common problems:
- Something is hogging the serial port.
e.g. TunerStudio, modem or mobile phone cable software.
Be sure to close/exit those applications.
- USB-serial cable on high COM port number, use Device Manager to re-assign
it to say COM1.
- ECU not powered up, be sure there is fused power applied. Use a mains
adapter or vehicle battery. PP9 batteries are too feeble.
- Serial cable not connected correctly
- Software driver problems
Check the above. Do you want to try probing again? (y/n default = y)
NEW CHECK (3)
MegaSquirt-3 Firmware Loader 3.45 2017-01-16
---------------------------------------------------------------------------
This firmware loader is only licensed for loading Megasquirt firmware onto
official Megasquirt hardware.
Using Megasquirt firmware on un-approved devices is in breach of copyright.
Visit Megasquirt EFI - Fuel injection and Ignition Control ECU to check the validity of your hardware.
-----------------------------------------------------------------------------
Remove the fuse powering your ignition coils.
(Spark outputs may be undefined until you re-load your settings.)
Press enter to continue...
Ensure that your Megasquirt/Microsquirt/ECU is
-connected to your computer
-has fused 12V power connected.
Press enter to continue...
Ensure that no tuning software is running.
Be sure to Quit the software, not just minimise it..
Press enter to continue...
Debug message Level:
1: Normal
2: More detail
3: + serial comms
4: + the s19 file as parsed
Selection (default: 1): 3
Do you want to scan your serial ports automatically? (y/n default y)
Trying: COM1 ..#Opening comm port COM1
(\\.\COM1)
COM1 does not exist.
couldn't open port
#Comm port already closed
Trying: COM2 ..#Opening comm port COM2
(\\.\COM2)
COM2 does not exist.
couldn't open port
#Comm port already closed
Trying: COM3 ..#Opening comm port COM3
(\\.\COM3)
COM3 does not exist.
couldn't open port
#Comm port already closed
Trying: COM4 ..#Opening comm port COM4
(\\.\COM4)
COM4 does not exist.
couldn't open port
#Comm port already closed
Trying: COM5 ..#Opening comm port COM5
(\\.\COM5)
TX: 51
Waiting...
Waiting...
Sent Q and got 0 bytes back.
TX: 0d
Waiting...
Waiting...
Sent 0d and got 0 bytes back #Closing comm port
Trying: COM6 ..#Opening comm port COM6
(\\.\COM6)
COM6 does not exist.
couldn't open port
#Comm port already closed
Trying: COM7 ..#Opening comm port COM7
(\\.\COM7)
COM7 does not exist.
couldn't open port
#Comm port already closed
Trying: COM8 ..#Opening comm port COM8
(\\.\COM8)
#Comm port already closed
WARNING!!!
No valid ports or ECUs found. Cannot load firmware without communications.
Common problems:
- Something is hogging the serial port.
e.g. TunerStudio, modem or mobile phone cable software.
Be sure to close/exit those applications.
- USB-serial cable on high COM port number, use Device Manager to re-assign
it to say COM1.
- ECU not powered up, be sure there is fused power applied. Use a mains
adapter or vehicle battery. PP9 batteries are too feeble.
- Serial cable not connected correctly
- Software driver problems
Check the above. Do you want to try probing again? (y/n default = y)
#12
Senior Member
iTrader: (1)
Join Date: Dec 2010
Location: Farmington Hills, MI
Posts: 1,218
Total Cats: 175
What cable are you using? Does it use an FTDI chip? If so, do you have FTDI drivers? Have you ensured the MS is getting a full 12V? Have you checked device manager to make sure the USB cable is being recognized and is assigned a COM port?
This is usually my thought process when I can't connect.
This is usually my thought process when I can't connect.