masblue

sup guys i just picked up a used Greddy Turbo kit for my miata but is missing little small stuff. i was wondering where i could buy them?? and can i buy this from Greddy??

stuff i need:
oil return pipe
oil pressure hose 800mm
oil pressure hose banjo union,small,male
oil pressure hose banjo union,small,female 10 x 1.24
union hose fitting straight 1/8 pf - m10 x p 1.50
union hose fitting
oil return hose (i want the braided one)
fuel line 8mm x 500mm

miata-turbo08

iTrader: (1)

damn they didn't give you that stuff?? well greddy for a fact takes a longggg time on that kind of stuff if you tell them its missing and wait for them to ship it you could have got the oil hose parts and had it made for cheaper by then..

masblue

i dont want to wait dat long.. i guess i jst have to get it some where else but where??

Fergus

Do like the majority of Greddy kit owners do for the return line - tap the oil pan and be done with it !

miata-turbo08

iTrader: (1)

the return like is just like a rubber tube that goes to a nipple on the left of the engine that is capped off right under the alternator by the oil filter so that tubing can be braided that won't be a problem to get at a hardware store.. as for the oil feed line it could also be purchased at an auto store. or hardware if you know what your looking for. youll have to have the right ends on each end. like around here we have Napa auto parts and they do stuff like that.

clay

iTrader: (6)

masblue, be sure and search before posting a question. This board isn't very tolerant of newbie questions. To help answer your question though, see this link:
https://www.miataturbo.net/forum/sho...&highlight=OIL

I just purchased all new oil supply parts as my used Greddy kit was missing some stuff as well. I can't help with the oil drain as I used 5/8 hose and a heater hose bung, not SS line. I did drill and tap the pan though. Enjoy the extra horses!

masblue

my bad but i did search before i post..i guess i didnt search hard enough but thanks for the help you guys. i will post pictures of my car when its complete

masblue

clay what about the oil pressure hose and the fuel line can i get it from the same website and which one would you recommend. and do you have any picture of your greddy set up?

tnxs

clay

iTrader: (6)

Here are some pics from my install. No sign-in required.
http://www.kodakgallery.com/I.jsp?c=...&x=0&y=-3yxgmd

The "oil pressure hose" that Greddy is calling out is replaced by the -3 SS line in my setup:
ANPlumbing 63010132 -3AN SS line Female swivel both ends, -3 hose, 32" long $14.69

Basically if you order the parts I listed, it will be every part you need for the oil supply.

The fuel line is just a short section of 5/16" (I think) fuel hose to go from the Vortech back to the hard line. You can get that at Napa, Autozone, etc. 1-2 feet should be plenty.

masblue

Thanks Clay for you Help. it help me a lot. and Nice car. white on white i like that!!

FHS

iTrader: (2)

Sorry if this is obvious, but make sure the fuel line you get is for fuel injected applications.

masblue

got it!! and one more thing do i have to update my ecu or i could use the stock one

Dow.tom

iTrader: (3)

you can use your stock ECU. The FPR will raise the base fuel pressure. But like someone else will probably say... MS is the way to go and will save you hassle and time in the end. 700 for PNP 300 for DIY

masblue

Oic...i think i would to in the future when i start boosting more
tnxs for the info