Leaking between turbo and manifold...bolts are tight
02-01-2009, 06:36 PM
#1
Tour de Franzia
Thread Starter
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
Leaking between turbo and manifold...bolts are tight
I have the begi manifold and the manifold and turbo flanges were surfaced before installing, and just a little exhaust is leaking out. The bot are very, very tight.
I also noticed that when the car is cold, it doesn't like to make boost, which scared me, but when it gets hot it drives fine...are the surfaces expanding and sealing?
should I take these off and have them surfaced again?
Time to safety wire or go stage-8...anyone know if stage-8 hardware will fit a gt2860rs turbine housing?
I also noticed that when the car is cold, it doesn't like to make boost, which scared me, but when it gets hot it drives fine...are the surfaces expanding and sealing?
should I take these off and have them surfaced again?
Time to safety wire or go stage-8...anyone know if stage-8 hardware will fit a gt2860rs turbine housing?
Reply
0
0
02-01-2009, 06:59 PM
#2
If they're flat, put some heavy grease on the two surfaces and bolt it back up. My manifold NEEDED to be surfaced. I literally used a file to get it decent, then heavy grease, bolted that **** together, and after the grease burned and carbon'd up, no more leak. My turbo bolts aren't very very tight either. Just snugged good, probably 20 ft*lbs.
Reply
0
0
02-01-2009, 07:42 PM
#5
Elite Member
iTrader: (1)
Join Date: Feb 2008
Location: Birmingham Alabama
Posts: 7,930
Total Cats: 45
Yes, overly tight in most cases is worse than loose (not in all cases 
). Ive tried to get this through my dad head for years. He likes to tighten it until he either breaks a tool, or the bolt. Tight doesnt mean sealed. Which is why there are torque specifications. That grease thing seems like a good idea.
). Ive tried to get this through my dad head for years. He likes to tighten it until he either breaks a tool, or the bolt. Tight doesnt mean sealed. Which is why there are torque specifications. That grease thing seems like a good idea.
Reply
0
0
02-01-2009, 08:07 PM
#6
I have the same problem with my s4 mani. I didn't have the problem before tracking the car with the damn turbo blanket on. After the track day torched the blanket I had the exhaust leak. Too much heat must have warped something slightly. BEGI sent me a couple types of gaskets to use to seal it up. I'm too lazy and havent gotten around to sealing it up yet.
Reply
0
0
02-01-2009, 08:24 PM
#7
Elite Member
iTrader: (1)
Join Date: Feb 2008
Location: Birmingham Alabama
Posts: 7,930
Total Cats: 45
What kind of gaskets are you guys using? I know my old RX7 had one of those 1 piece aluminized looking soft gaskets, looked like some kind of fiber coated with foil. They sucked major ***. I cant see how a MLS style gasket would leak so easily, as to be better to run without one.
Reply
0
0
02-01-2009, 09:19 PM
#9
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,645
Total Cats: 3,008
Why? Either...
Remove. Grease. Go dyno that bastard.
Or...
Remove. Flat file. Grease. Go dyno that bastard.
Which of the above depends on how much gap you are dealing with.
After all of the crap you have endured, don't let this little stuff stand in your way. And yes, it is a PITA to even have to deal with it.
Good luck.
Remove. Grease. Go dyno that bastard.
Or...
Remove. Flat file. Grease. Go dyno that bastard.
Which of the above depends on how much gap you are dealing with.
After all of the crap you have endured, don't let this little stuff stand in your way. And yes, it is a PITA to even have to deal with it.
Good luck.
Reply
0
0
02-01-2009, 10:13 PM
#11
Tour de Franzia
Thread Starter
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
Reply
0
0
02-02-2009, 12:03 AM
#15
Elite Member
iTrader: (1)
Join Date: Feb 2008
Location: Birmingham Alabama
Posts: 7,930
Total Cats: 45
Wouldnt imagine it would hold up with much of a gap though. The times Ive used to stuff it never fully hardens, and would probably eventually be blown out from pressure and heat. Probably works fine for a very minor difference in surfaces. Its only rated to 700 or 800 degrees as I recall.
Reply
0
0
02-02-2009, 08:10 AM
#16
Wouldnt imagine it would hold up with much of a gap though. The times Ive used to stuff it never fully hardens, and would probably eventually be blown out from pressure and heat. Probably works fine for a very minor difference in surfaces. Its only rated to 700 or 800 degrees as I recall.
My turbo header was not built very well. It looked good but the surface was not very true. No gasket would work. The stuff I mentioned fixed it. This was on a 600 plus RWHP turbo mustang. It lasted through drag strip passes and daily driving. I also used it on te turbo flange. Just relaying my experience.
Reply
0
0
02-02-2009, 08:43 AM
#17
Elite Member
iTrader: (1)
Join Date: Feb 2008
Location: Birmingham Alabama
Posts: 7,930
Total Cats: 45
My turbo header was not built very well. It looked good but the surface was not very true. No gasket would work. The stuff I mentioned fixed it. This was on a 600 plus RWHP turbo mustang. It lasted through drag strip passes and daily driving. I also used it on te turbo flange. Just relaying my experience.
Reply
0
0
02-02-2009, 09:12 AM
#19
Over a year. It was still holding when I sold the car. It was recommended to me by the guy that built my motor. Honestly, I was skeptical, but it was that, or send the parts back for the gazillionth time to the company I bought my kit from. I had a **** load of fitment issues, and they were not very good at getting **** resolved. Parts didn't fit, parts left out of the package, they would tell me ***** coming in a week and it would take months, The turbo they sent me was busted right out of the box, etc. I figured WTF, give it a shot, since the guy that built my motor knew his **** I took his word for it. It worked.
Reply
0
0
