Guys with "built" (forged) engines
#1
Elite Member
Thread Starter
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
Guys with "built" (forged) engines
How many of you guys with forged bottom ends just tossed the pistons and rods in with little to no machining?
i have been interested since i have been hearing from most here that they havent balanced the engine internals and have been using it for XX years.
i would love pistons and rods in the short term but the balancing and machining costs in my area cost more than the parts which breaks the budget. on the inverse im not going to toss some gang parts in and blow **** up in a week.
Matt
i have been interested since i have been hearing from most here that they havent balanced the engine internals and have been using it for XX years.
i would love pistons and rods in the short term but the balancing and machining costs in my area cost more than the parts which breaks the budget. on the inverse im not going to toss some gang parts in and blow **** up in a week.
Matt
#6
Elite Member
Thread Starter
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
I remember there being a thread on what machining is reccomended, but i cant find it with the search.
if you have done machining what have you done, what is needed and what is gravy?
if you just do a bore/hone and a full balance thats not too bad... but the builders here are slinging all of this crap around about high boosted street builds.
if you have done machining what have you done, what is needed and what is gravy?
if you just do a bore/hone and a full balance thats not too bad... but the builders here are slinging all of this crap around about high boosted street builds.
#7
A simple crank balance and polish should cost $120-$150 up here in Canada. Then it's up to you how much further you take it. You can balance everything or match it as closely as possible by weighing everything. A bottom end done like that should spin to 8k without any problems.
Ignore what all the "builders" are saying. Just bore/hone, balance/polish the crank and balance your pistons, rods and rings as closely as you can my mixing and matching. You can tKe it one step further and take material off the underside of the piston in tiny amounts to match it perfectly. Anyone charging you more that $30/hole and $150 for the crank is charging too much n
Ignore what all the "builders" are saying. Just bore/hone, balance/polish the crank and balance your pistons, rods and rings as closely as you can my mixing and matching. You can tKe it one step further and take material off the underside of the piston in tiny amounts to match it perfectly. Anyone charging you more that $30/hole and $150 for the crank is charging too much n
#8
Elite Member
Thread Starter
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
the balancing quotes i have been getting are in the area of $350 and bore/finish coming in at $45 per hole ($180 total)
polishing the crank is necessary, or is that gravy?
so if i essentially wanted pistons and rods so i can toss some real boost in it with a stock VVT head i would be looking at:
-pistons
-rods
-bearings
-head gasket
-balanced
-bore/hone
everyone here is trying to add line-hone @180$, knife edging at $250 (iirc) and some weird tempering and crap to the block.
-Matt
polishing the crank is necessary, or is that gravy?
so if i essentially wanted pistons and rods so i can toss some real boost in it with a stock VVT head i would be looking at:
-pistons
-rods
-bearings
-head gasket
-balanced
-bore/hone
everyone here is trying to add line-hone @180$, knife edging at $250 (iirc) and some weird tempering and crap to the block.
-Matt
#9
I got bore/hone w/ torque plate and line bored for $325, was told knife edging was overkill for a street car.
Also, so long as you're doing all this get:
new water/oil pump (with fancy gears, of course)
full engine gasket set
arp head/main studs
belts/hoses
coolant re-rout
Then, once again while you're in there:
headwork
valve seals
fancy valves/springs (I'm trying to resist doing this)
And you'll be 4-5k in the hole with the rest of us!
Also, so long as you're doing all this get:
new water/oil pump (with fancy gears, of course)
full engine gasket set
arp head/main studs
belts/hoses
coolant re-rout
Then, once again while you're in there:
headwork
valve seals
fancy valves/springs (I'm trying to resist doing this)
And you'll be 4-5k in the hole with the rest of us!
Last edited by chokeasphyxia; 03-10-2011 at 03:55 PM. Reason: remembered more engine stuff
#10
Elite Member
Thread Starter
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
the "while your in there" thing is the whole reason i made this thread.
headwork, fancy valves and random useless **** like that pushes most builds to the 4-5k range.
i want to take my GOOD VVT engine and just put basic pistons and rods in. keep costs low for other things that fail when im racing this summer.
headwork, fancy valves and random useless **** like that pushes most builds to the 4-5k range.
i want to take my GOOD VVT engine and just put basic pistons and rods in. keep costs low for other things that fail when im racing this summer.
#11
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
A simple crank balance and polish should cost $120-$150 up here in Canada. Then it's up to you how much further you take it. You can balance everything or match it as closely as possible by weighing everything. A bottom end done like that should spin to 8k without any problems.
Ignore what all the "builders" are saying. Just bore/hone, balance/polish the crank and balance your pistons, rods and rings as closely as you can my mixing and matching. You can tKe it one step further and take material off the underside of the piston in tiny amounts to match it perfectly. Anyone charging you more that $30/hole and $150 for the crank is charging too much n
Ignore what all the "builders" are saying. Just bore/hone, balance/polish the crank and balance your pistons, rods and rings as closely as you can my mixing and matching. You can tKe it one step further and take material off the underside of the piston in tiny amounts to match it perfectly. Anyone charging you more that $30/hole and $150 for the crank is charging too much n
lol @ spinning a Miata to 8000rpm. I'm just a layman, but I've seen my engine beat the turbo to death with vibration at <7k and would never go higher with this motor.
I agree with the cost/benefit ratio. Hit the big stuff that make the engine reliable and take that last $1000 you'd spend on removing material and porting to the suspension fund because I promise you'd get more bang for your buck out of half a set of Xidas over 10hp from a p&p.
#13
Just do a basic balance, matching things up with a decent scale as best as you can. For a street car, full balancing and blue printing is a little over kill. Get the cylinders bored and honed. Maybe polish the crank if it needs it. Take a dremel to the cylinder head. Just do a gasket match and knock as much of the casting marks out as you can, nothing serious. All that takes is time and a few cans of brake parts cleaner to get the shavings out. You don't even have to remove the valves to do that one.
#14
I'm going to get berated for admitting this, but I only put rods in my car. I blew a headgasket, decided to pull it, put a new gasket in and eagle rods. I reused my stock pistons, bearings, headstuds, etc and did no machine work at all. I just put it all back together and I've got probably 10k on that motor that's seen up to 18psi without any complaints so far.
#15
I actually have a few questions that are somewhat similar to this. I'm looking to do a budget build. (I.E. student budget) Ive got a torn down 94 block that im looking to build. What are your thoughts on forged rods, everything else stock and a complete rebuild?
I dont have a turbo as of yet. but I'm looking for a trackable 240 hp down the line. Thoughts, Suggestions? Should I hold out for some pistons while I am at it? will stock 94 pistons hold to 240 safely?
Edit: ^sort of to the extent of what hes done. Except with machinework and a homebrew balance job.
I dont have a turbo as of yet. but I'm looking for a trackable 240 hp down the line. Thoughts, Suggestions? Should I hold out for some pistons while I am at it? will stock 94 pistons hold to 240 safely?
Edit: ^sort of to the extent of what hes done. Except with machinework and a homebrew balance job.
#16
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,099
My limiter is set at 7400 for a reason.
You must hone the motor, that's not optional. It is HIGHLY recommended that you bore the motor, unless you are having custom pistons specifically created to match your bore sizes with the proper wall clearances. Start with a running motor and nothing else is needed, IMO - neither of my built motors had any additional balancing done beyond matched pistons/rods.
#17
Elite Member
iTrader: (10)
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,977
Total Cats: 356
I have datalogged WOT sessions of 110 seconds. Literally WOT for 110 seconds on 5th gear. Several of those were at 7500-7600. Granted, only one such datalog. Do I stay at 7500+ for more than a few seconds each time? No, I shift. I first installed my MS in July of 2006. 5 years later and this engine is still here.
How many times have I gone above 7500? If only twice per day (way more), then in 5 years, and if only lasts 1 second every time, that's roughly sixty minutes spent above 7500rpm.
Maybe the USDM engine is different, maybe you track guys alter something but don't share, I don't know. My own engine has exactly Z E R O failures in the 5 years of being MSed and being pounded a little too much.
How many times have I gone above 7500? If only twice per day (way more), then in 5 years, and if only lasts 1 second every time, that's roughly sixty minutes spent above 7500rpm.
Maybe the USDM engine is different, maybe you track guys alter something but don't share, I don't know. My own engine has exactly Z E R O failures in the 5 years of being MSed and being pounded a little too much.
#18
Elite Member
iTrader: (10)
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,977
Total Cats: 356
First, it was "overheating" each time.
Then it was the VVT that was switched on at the setpoint with the TEC2, rather than progressively retarded and destroyed the head.
The the Hydra was fitted and now its the sustained high-RPM operation that causes the failure.
So what is it?
#19
IF the bores are in very good condition you can get away with new rings and a HONE.
Said hone can be a DIY job using a brush hone. The hone is needed for the new rings to seat.
www.brushresearch.com
There is some technique to it...
Said hone can be a DIY job using a brush hone. The hone is needed for the new rings to seat.
www.brushresearch.com
There is some technique to it...
Last edited by JasonC SBB; 03-10-2011 at 08:12 PM.