Twitchy car (tail happy problem)
#1
Junior Member
Thread Starter
Join Date: Feb 2012
Location: Quebec city, Canada
Posts: 172
Total Cats: 2
Twitchy car (tail happy problem)
Hey guys,
Trying to understand what is wrong with my car. Car is very tail happy, very difficult to catch when it starts to oversteer, especially in auto-x. On the track I put back on the rear swaybar (oem 1.6 swaybar), the car feels more neutral, but tail happy in corner entry. Quick transitions and slippery surface make it worst. Been trying to adapt my driving to it, which still gives me pretty good results, but drove a very well setup car yesterday (thanks Joyrider! VVT, Xidas, 15x9 Nt01, Torsen, aero) and there is definitely something wrong with the balance of my car...
I have a few ideas on what might be causing the problem, just want your opinions. Car is 1990 miata, 1.8 swap, open diff,949 no aero.
Setup:
Suspension: koni race shocks (I believe I have the ones with the really short rear shocks), NA top mounts, 700-400lbs/in springs. Koni front bump stops, fatcat 36mm rear bumpstops, 1.125 hollow front bar, no rear bar.
Alignement: -3.0deg front camber, 4deg caster, -2.5 rear camber, 0 toe all around.
Ride height: 4in pinch weld front, 4.25in pinch weld rear.
Wheels/tires: 15x8 +25 konig wideopen, 205-50-15 rivals
Thanks for your input,
Ben
Trying to understand what is wrong with my car. Car is very tail happy, very difficult to catch when it starts to oversteer, especially in auto-x. On the track I put back on the rear swaybar (oem 1.6 swaybar), the car feels more neutral, but tail happy in corner entry. Quick transitions and slippery surface make it worst. Been trying to adapt my driving to it, which still gives me pretty good results, but drove a very well setup car yesterday (thanks Joyrider! VVT, Xidas, 15x9 Nt01, Torsen, aero) and there is definitely something wrong with the balance of my car...
I have a few ideas on what might be causing the problem, just want your opinions. Car is 1990 miata, 1.8 swap, open diff,949 no aero.
Setup:
Suspension: koni race shocks (I believe I have the ones with the really short rear shocks), NA top mounts, 700-400lbs/in springs. Koni front bump stops, fatcat 36mm rear bumpstops, 1.125 hollow front bar, no rear bar.
Alignement: -3.0deg front camber, 4deg caster, -2.5 rear camber, 0 toe all around.
Ride height: 4in pinch weld front, 4.25in pinch weld rear.
Wheels/tires: 15x8 +25 konig wideopen, 205-50-15 rivals
Thanks for your input,
Ben
#2
Usually it would be a combination of stiffening the front and softening the rear to trend towards understeer. Sounds like you've already done a fair bit of that.
My guess is you're running out of rear shock travel and hitting the bump stops back there hard enough to break traction. Change rear tophats to get more travel? Trim the rear bump stops? Run lower tire pressure on the rear? Soften the rear shock settings relative to front?
Also, smooth is fast.
My guess is you're running out of rear shock travel and hitting the bump stops back there hard enough to break traction. Change rear tophats to get more travel? Trim the rear bump stops? Run lower tire pressure on the rear? Soften the rear shock settings relative to front?
Also, smooth is fast.
#3
Junior Member
Thread Starter
Join Date: Feb 2012
Location: Quebec city, Canada
Posts: 172
Total Cats: 2
Yeah, thought about that, but I'm afraid I will loose the very little bump travel I have with the rear shock I have, and the bump stops are all ready shorts... lol.
With my car, I HAVE to be smooth, or else I loose it. Yesterday, with Joyrider's car, I could just do whatever I wanted to it, and it would take it beautifully...
I think a LSD would help a lot, and I'll also try to run the FSB to the stiffer setting. After that I'll play with damping...
With my car, I HAVE to be smooth, or else I loose it. Yesterday, with Joyrider's car, I could just do whatever I wanted to it, and it would take it beautifully...
I think a LSD would help a lot, and I'll also try to run the FSB to the stiffer setting. After that I'll play with damping...
#6
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,099
No, it doesn't need to go higher. I ran those exact shocks with 700/450 springs at those ride heights with similar camber/toe numbers and that front sway bar, and the car was essentially perfect. The 8041 RACE shocks have super short bodies, so running them with NA tophats is what you should be doing - running NB hats lifts the shock shaft up even further and trades droop travel you desperately need for bump travel you can't use. I actually ran a bit more rear sway at one point (MSM RSB) as I thought the car pushed a bit.
OP, if you want something to try, you can drop the rear end 2 turns at a time and see what that does, but I'm leaning towards a loose alignment bolt or some other deflection that's causing this, since I ran a very similar setup with great success for a long time. It almost sounds like dead tires - how old is the rubber and does it sit out in the winters?
OP, if you want something to try, you can drop the rear end 2 turns at a time and see what that does, but I'm leaning towards a loose alignment bolt or some other deflection that's causing this, since I ran a very similar setup with great success for a long time. It almost sounds like dead tires - how old is the rubber and does it sit out in the winters?
#7
Junior Member
Thread Starter
Join Date: Feb 2012
Location: Quebec city, Canada
Posts: 172
Total Cats: 2
Thanks for your inputs guys!
Sav: Rake was an other one the list I definetly wanted to play with, just don't want to change too many things at the same time...haha. Alignement was checked 2 weeks ago, nothing is loose. Tires are on their 2nd summer, stored inside during the winter, maybe 8000 km, 2 lapping nights and maybe 60-70 slalom runs. About 3-4/32in left on the thread. They are not new for sure, but still look and grip decent.
Dropping the coils 2 turns just drop about a quarter in at the pinch weld?
Ben
Sav: Rake was an other one the list I definetly wanted to play with, just don't want to change too many things at the same time...haha. Alignement was checked 2 weeks ago, nothing is loose. Tires are on their 2nd summer, stored inside during the winter, maybe 8000 km, 2 lapping nights and maybe 60-70 slalom runs. About 3-4/32in left on the thread. They are not new for sure, but still look and grip decent.
Dropping the coils 2 turns just drop about a quarter in at the pinch weld?
Ben
#10
I had a similar issue where the car rotated too quickly on corner entry to mid corner. Eventually I eliminated the issue by making sure my rear bumpstops were shorter than the front. I'd suggest getting a ground control 45 mm bumpstop and cut it down to about 30mm and see if that tames the rear.
Last edited by wannafbody; 09-08-2015 at 09:53 AM.
#13
Junior Member
Thread Starter
Join Date: Feb 2012
Location: Quebec city, Canada
Posts: 172
Total Cats: 2
The more I think about it, dead tires seem plausible... 2 years ago, when I was running tires that were certainly dead, the car was doing pretty much the same thing as it is doing now... I'll still try to balance it out, but new tires will be coming in next year.
For those who ran this setup, do you think upgrading to 15x9 with 225-45-15 Nt01 or maxxis RC1 will be too much for these spring rates?
Thanks!
Ben
For those who ran this setup, do you think upgrading to 15x9 with 225-45-15 Nt01 or maxxis RC1 will be too much for these spring rates?
Thanks!
Ben
#15
I had a similar issue where the car rotated too quickly on corner entry to mid corner. Eventually I eliminated the issue by making sure my rear bumpstops were shorter than the front. I'd suggest getting a ground control 45 mm bumpstop and cut it down to about 30mm and see if that tames the rear.
Car is awesome and do what you want it to do ! I beat all my track times since ditching the turbo and having so much problem those last 2-3 years... now need more seat time and enjoy the car.
#16
The more I think about it, dead tires seem plausible... 2 years ago, when I was running tires that were certainly dead, the car was doing pretty much the same thing as it is doing now... I'll still try to balance it out, but new tires will be coming in next year.
For those who ran this setup, do you think upgrading to 15x9 with 225-45-15 Nt01 or maxxis RC1 will be too much for these spring rates?
Thanks!
Ben
For those who ran this setup, do you think upgrading to 15x9 with 225-45-15 Nt01 or maxxis RC1 will be too much for these spring rates?
Thanks!
Ben
#17
The more I think about it, dead tires seem plausible... 2 years ago, when I was running tires that were certainly dead, the car was doing pretty much the same thing as it is doing now... I'll still try to balance it out, but new tires will be coming in next year.
For those who ran this setup, do you think upgrading to 15x9 with 225-45-15 Nt01 or maxxis RC1 will be too much for these spring rates?
Thanks!
Ben
For those who ran this setup, do you think upgrading to 15x9 with 225-45-15 Nt01 or maxxis RC1 will be too much for these spring rates?
Thanks!
Ben
Thread
Thread Starter
Forum
Replies
Last Post
eddy1128
Miata parts for sale/trade
8
12-10-2015 05:34 PM