motorphile

iTrader: (1)

It looks like I'm a little late to the party, but I'll take two sets. Thanks for bringing this to fruition.

hi_im_sean

iTrader: (3)

as long as no one flakes out, we are at 18, ill go ahead and make that 20. congrats everyone we are at $79 a set! pms going out momentarily to start collecting $$$

nota4re

Hi Sean, I'm too new to have the ability to send or respond to your PMs. Just want you to know I did receive the PM and I paid for the 5 sets via Paypal a moment ago. I added 3% to the total you provided to cover the paypal fees. Thanks again for doing this.

hi_im_sean

iTrader: (3)

everyone has been PMed

making a new list for payment status
user-qty-status
1. glade-1-out
2. Gee Emm-2-paid
3. 90civichhb-1-paid
4. TNTUBA-1-paid
5. mcfandango-1-paid
6. stoves-1-paid
7. hingstonwm-2-paid
8. nota4re-5-paid
9. Dustin1824-1-paid
10. hrk-1-paid
11. motorphile-2-paid
12. stevemhudson-1-paid

hi_im_sean

iTrader: (3)

got it! i was wondering what the extra was for, but PP fees are included in the pricing. ill refund you the extra when i get a moment.

stevemhudson

Can't send a PM. I'd like a set, if you have any left.

hi_im_sean

iTrader: (3)

2 sets left, PM sent

hi_im_sean

iTrader: (3)

snap rings and aluminum stock have been ordered. im going to go visit the machine shop tomorrow to give them money and finalize the details. ive been given an eta of 1.5-2 weeks. i should have the spacers done within that time frame so im hoping to ship around the end of the month. thanks for the quick payment everyone.

hi_im_sean

iTrader: (3)

18 sets paid for and someone canceled so 2 sets left available for sale!

Oscar

iTrader: (2)

Qoute for 1 set shipped to the UK?

hi_im_sean

iTrader: (3)

$99

Leafy

iTrader: (1)

I put mine in this weekend. I wish we went with a more generous chamfer on the side that we push the spherical in from and I also wish that we made that bore so it would have been a very slight clearance on the spherical.

hi_im_sean

iTrader: (3)

Mine slid right in with 0 effort, did you sand the bore clean?

If the bearing is a slip fit in the bore it will pound the snap ring out, especially if you are making power and running slicks. This assumes you install the shoulder in the braking force direction (to the rear). Installing the other way would be even worse. It would be to difficult to machine a snap ring groove in such a way as to reduce slop to 0. Especially when the aouras seem to be at least +/- 0.002".

Do you want some 7075 spacers?

ftjandra

iTrader: (6)

Could always install the bearing with the same green loctite.

--Ferdi

Leafy

iTrader: (1)

no no, just from the outside edge to the snap ring would have been nice to be a hair over a press fit. The fit where the bearing sits was perfect. The hardest part was getting the bearing into the sleeve straight. Once I had the 2nd one half way in I realized I should have installed the sphericals with the sleeves out of the car.

hi_im_sean

iTrader: (3)

oh i got ya. the machinist said he was going to make the bore outside the snap ring groove just a little larger on the production run. not a free fit, but not as tight of a press fit either. and yea its way easier to put them on an arbor press/vice/hydraulic press before the are in the car.

i made an install tool for the bearing that can be whored around for those that are interested. just pay shipping to the next guy. or ship your bearings to me and ill press them in for you.

hi_im_sean

iTrader: (3)

This came in today.

bbundy

The full set of low friction bushings sleeves for urethane.

cordycord

iTrader: (2)

Bronze outers with steel centers? These take the place of the steel bushings, and (I assume) are the same thickness so the urethane doesn't need to be hogged out? If so, very cool!

bbundy

yep. low friction pivot sleeves for on the inside of off the shelf urathane bushings. I switched material and made them out of 4340. should be tough eoungh I think.