TURNS101

iTrader: (10)

I will be receiving these items soon.

EMS-1st gen


HD meth injection kit w/ filter.


Water/Meth Flow Gauge


Intake Air Temp Sensor


3.5 bar map sensor.


O2 sensor


serial gauge kits.


Adjustable Fuel pressure regulator


Boost control solenoid



Plug and Pin kit for 30-6050

I think I will also get a coolant sensor from AEM.

I have the coils and timing wheel from the Tech that I plan to use.

Couple questions:

The coils and timing wheel should work correctly?
I dont have any stock sensors in there for timing.
I have low imp 880 injectors. Do low imp work with it?
Will I be able to use my current TPS ?
Will I be able to use my current IAC ?
If I can use the stock TPS and IAC, what do I need to know about scaling for them??

This is a 1.8 block with 99 head.

I plan to actually document this build and have pics and dyno info for you

Thanks everyone. I look forward to joining the AEM team.

Jeff

JasonC SBB

You'll need resistors (like from an Accord) to run lo imped injectors.

Some have had trouble using a 60-2 wheel with the AEM. IMO a 12 or a 12-1 is best.

You can use the factory sensors.

What is a 30-6050?

More later.

rbluemx6

iTrader: (2)

I looked up that part number and it seem to be a series 2 unit for honda/acura diy harness kit.

Should, but not sure how to make it work.


Must use resistors.

Thats about all I can answer right now.

shlammed

iTrader: (8)

TPS will work, set the throttle range with the wizard, and then go in and change the values to read from 1% minimum to 95% maximum to work the smoothest on throttle based maps.

TURNS101

iTrader: (10)

More later is good.

Thank you

Jeff_Ciesielski

iTrader: (10)

Resistors are easy, just get some 10 ohm 20 watt resistors and wire them in-line with the power feed to the injectors. Its a really quick and easy job, takes about 20 minutes.

TURNS101

iTrader: (10)

Cool, thanks Jeff.

I am pretty excited about teaming up with AEM. I think the car will become more serious now.

I say **** the 6 speed. I will show you guys what power will break it

JasonC SBB

Series 2 may be happy with 60-2 wheel, I dunno.
May also work with lo imped injectors.

I've never played with the S2 software. In the S1, the main board was all the same so you could adapt any board to any car with some minor differences in what inputs/outputs were brought out to the connectors. The trigger setup could be changed in the tuning software ("AEMPro") to work with any trigger wheel than any AEM worked with and more.

If you will use a for-Acura model you will want an adapter harness or hardwire it to the car using junkyard Acura mating connectors. (this is what I did with my seres 1 for-1995-Honda-AEM into my 2000)

TURNS101

iTrader: (10)

Jason, this is a series 1 computer.

I will have to ask they guys at roadrace engineering if they have seen the series 1 with a 60 tooth wheel.

I can also just call aem

If you will use a for-Acura model you will want an adapter harness or hardwire it to the car using junkyard Acura mating connectors. (this is what I did with my seres 1 for-1995-Honda-AEM into my 2000)

This is in regard to the injectors then, yes?

JasonC SBB

no I was talking about connecting the AEM to the car.

TURNS101

iTrader: (10)

All of the sensors I have, stock or not are hooked up to the Tech system right now. The stock harness isnt in there.

The AEM will be run to each thing individually, like the Tech is now.
coils
timing wheel
injectors
IAT
MAP
That's about it.
Plus what ever the hell the meth/water injection uses. I dont know anything about that system.

TURNS101

iTrader: (10)

Small update.

I receieved a Series 2 EMS.
Pretty excited...

Rafa

iTrader: (22)

Wow! That's a good score!

I think you're the first to use it in a Miata.

TURNS101

iTrader: (10)

Yeah, I am pretty stoked. My tuner is a AEM master too. So it should be really awesome.

I am excited to see how the water/meth system works too.

I want to leave at about 360 or so whp/ftlbs. I think it will be pretty easy to do no higher than 25psi with spool I will be OK with. I believe I am at 20.9 psi with my 330hp and 316ftlbs. So with a new/better system for my tuner and water/meth, i think my goal will be easy.

I would go to about 27psi and see what happens, but I am scared to blow apart the 6 speed on my 1st run

TURNS101

iTrader: (10)

Do any of you kind folks know the ohm ranges for the
Fuel level sensor
TPS
oil pressure

TIA!!

aznDragonX

iTrader: (5)

I wonder what's stronger than 6-speeds tranny that we can put into Miata. Saw a few 6-speeds blown up from turbo miata in last couple months.

Rafa

iTrader: (22)

Ask Jason or J_man. I'm sure one of them will know.

Rafa

iTrader: (22)

A 5 speed from an RX-7 FD.

TURNS101

iTrader: (10)

Same as a TII and they break too. The guys I drive with all use beefier trans than the RX7 models because 2-3 a season were breaking.

I am think a muscle car trans. T10 or T5 something like that.. Just need the time to have it fabbed up.

Thanks for the names Rafa. i think jason has been following this a bit. I will see what he says. if not, I will PM him.

JasonC SBB

TPS you don't need to know - there's a setup routine you run to set the votlages at 0 and 100% TPS.

Dunno about fuel level and oil pressure. There are ways to figure it out.