Project Budget Time Attack.
#1
Project Budget Time Attack.
Wanted to thank everyone for your help with my several questions i had and I'm sure will continue to have with my build. The overall goal of my project is to be at the top of the horsepower/weight ratio for my time attack group which should be around ~150whp.
The following is what i currently have on the my list. Please point out anything I'm missing. Thanks again.
Turbo
Garrett TB2522
BEGI cast baffled manifold
BEGI stainless separated gas downpipe with extra o2 bung
BEGI Intercooler, piping, & bov
Turbo oil supply fitting
Turbo oil supply line, stainless
Turbo oil drain line, stainless
Engine oil supply fitting
Engine oil drain fitting
Turbo water supply fitting
Turbo water supply line
Turbo water drain fitting
Turbo water drain line
Manual boost controller (recommendations?)
1.8L Injectors or bigger
ECU
Innovate wideband and gauge
Mega squirt PNP (Brain built)
Coolant reroute
BEGI Spacer
BEGI Block off plate
Kia waterneck
GM Hose
Oil cooler
Flyin Miata thermostat kit
Cooler
Lines
Ill take any recommendations you guys send my way, thanks all.
The following is what i currently have on the my list. Please point out anything I'm missing. Thanks again.
Turbo
Garrett TB2522
BEGI cast baffled manifold
BEGI stainless separated gas downpipe with extra o2 bung
BEGI Intercooler, piping, & bov
Turbo oil supply fitting
Turbo oil supply line, stainless
Turbo oil drain line, stainless
Engine oil supply fitting
Engine oil drain fitting
Turbo water supply fitting
Turbo water supply line
Turbo water drain fitting
Turbo water drain line
Manual boost controller (recommendations?)
1.8L Injectors or bigger
ECU
Innovate wideband and gauge
Mega squirt PNP (Brain built)
Coolant reroute
BEGI Spacer
BEGI Block off plate
Kia waterneck
GM Hose
Oil cooler
Flyin Miata thermostat kit
Cooler
Lines
Ill take any recommendations you guys send my way, thanks all.
Last edited by v01canic; 07-18-2011 at 07:49 PM.
#4
MSPNP comes fully assembled, hence the name. It's the MS for we unwashed, solder-averse types. Did you mean DIYPNP?
www.megasquirtpnp.com
www.megasquirtpnp.com
#6
well the budget part went to ---- but here is some more info (also for some reason i cant edit my first post). I didnt do the coolant reroute or the oil cooler. Installed a water temp gauge coming right off the back of the head (temps dont exceed 215). I deleted the heater core and plumb right back into the mixing manifold. Oil temps are fine, reading off the drain plug.
So here are a few of the dyno graphs. Dotted line is after e85 solid line is before e85, 40 HP difference and a crap load more boost. We could have gone further but the actuator was too weak. We actually exceeded the limitations of the turbo and the injectors were at only 80% utilization. Boost went from ~10 PSI to ~17 PSI.
In order to keep in my Time Attack group (TA-B which is a 10/1 power to weight ratio) we had to reduce the horse power to 224.9.
So here are a few of the dyno graphs. Dotted line is after e85 solid line is before e85, 40 HP difference and a crap load more boost. We could have gone further but the actuator was too weak. We actually exceeded the limitations of the turbo and the injectors were at only 80% utilization. Boost went from ~10 PSI to ~17 PSI.
In order to keep in my Time Attack group (TA-B which is a 10/1 power to weight ratio) we had to reduce the horse power to 224.9.
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM