2jz Miata build thread
#765
Elite Member
iTrader: (12)
Join Date: Nov 2009
Location: Harpers Ferry WV
Posts: 1,516
Total Cats: 20
Here is what the connector looks like you can see it has two connectors and one bulk head. It is a 37 pin and the pins are roughly a 14 gauge wire not positive on that but I know they are big enough to do anything you need on a car.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
#769
Elite Member
iTrader: (12)
Join Date: Nov 2009
Location: Harpers Ferry WV
Posts: 1,516
Total Cats: 20
Got the harness finished up for the most part still need to finish wraping it with loom but it looks a whole lot better than the mess I started with.
[IMG][/IMG]
here are the connectors on the harness for easy in and out of the motor. Ignore the messy wires near the ecu side it looks worse than it really is. I am going to un pin a few wires to straighten it out, and the black wire with the red tracer is a power wire I need to trim before everything gets wrapped up.
[IMG][/IMG]
here is my power and ground wires witch will all be under the dash minus one ground by the coil.
[IMG][/IMG]
[IMG][/IMG]
here are the connectors on the harness for easy in and out of the motor. Ignore the messy wires near the ecu side it looks worse than it really is. I am going to un pin a few wires to straighten it out, and the black wire with the red tracer is a power wire I need to trim before everything gets wrapped up.
[IMG][/IMG]
here is my power and ground wires witch will all be under the dash minus one ground by the coil.
[IMG][/IMG]
#773
Elite Member
iTrader: (12)
Join Date: Nov 2009
Location: Harpers Ferry WV
Posts: 1,516
Total Cats: 20
Astroboy bought the connector I have but if anyone still wants one I have another one I ordered online that is a 50 pin but it is coming out of the Ukrain and will not be here until the middle of the month. I also picked up some single layer carbon fiber sheet that I am going to try and do my door panels in. I bought a set of plastic door cards off ebay so I think I can just get some double sided sticky sheet that is about 1/16 foam and lay the carbon fiber right over the plastic door car. I hope it turns out well if not I will have ruined a $100 set of door cars. But I will post pics to keep you all in the loop. My harness is officially done all wrapped up ready to go back in the car just waiting to go down and pull my dash out to start on the inside. I also ordered a new used turbo. This time I got a garrett T4 flanged T04B should be getting it in the mail soon. I am going to rebuild it and hopefully start out with a better turbo than before. We will see how it goes.
#774
Elite Member
iTrader: (12)
Join Date: Nov 2009
Location: Harpers Ferry WV
Posts: 1,516
Total Cats: 20
Here is a pic of my new turbo and I know it looks rough but it will look a lot better in a little while after it is rebuilt and cleaned up. Also here is a pic of the exhaust ring I got to go around my soon to be awesome fender exhaust. The turbo has a little bend on one of the fins I am getting a new compressor wheel and the good thing is it is big. Big enough for what I need.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
#779
Elite Member
iTrader: (12)
Join Date: Nov 2009
Location: Harpers Ferry WV
Posts: 1,516
Total Cats: 20
Hahahahaha lol I wish i had that turbo that thing is sick. This pic makes it look bigger than it really is not sure why. Maybe I am just used to looking at it now. Maybe one day I will have one like that.