Aidan's loose oily bunghole actually runs a track lap
10-09-2015, 09:02 PM
#4521
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Clearances are the same on all 4 corners. (Right, left, top, bottom)
@deezums Email me the drawings so I can confirm if the brackets match the drawings. If so the drawings need to be adjusted.
@deezums Email me the drawings so I can confirm if the brackets match the drawings. If so the drawings need to be adjusted.
Reply
0
0
10-10-2015, 12:22 AM
#4522
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
I'm a smart guy and was playing with the air compressor and killed my phone microphones. ****. Didn't want to buy another phone yet.
Reply
0
0
10-10-2015, 12:48 AM
#4523
lol
You might be able to replace just the microphone, sometimes they are on daughter modules.
The offset there should be 10.5mm or .413"
I still need to check mine, they aren't rubbing yet. Going to an autocross tomorrow so we'll see.
Metallic pads should rattle and groan a little when you roll or coast a bit with little brake pressure, right? That's the only thing I've noticed thus far, other than they clamp like ******* crazy.
You might be able to replace just the microphone, sometimes they are on daughter modules.
The offset there should be 10.5mm or .413"
I still need to check mine, they aren't rubbing yet. Going to an autocross tomorrow so we'll see.
Metallic pads should rattle and groan a little when you roll or coast a bit with little brake pressure, right? That's the only thing I've noticed thus far, other than they clamp like ******* crazy.
Reply
0
0
10-10-2015, 02:29 AM
#4524
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
I said fuckit and bought the same phone on ebay for $250. Its a bitch to take apart.
Did you measure the gap? Mine didn't rub until the track day.
Did you measure the gap? Mine didn't rub until the track day.
Reply
0
0
10-10-2015, 12:22 PM
#4529
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Yeah. I love my moto x. And there isn't anything else on the market like it. It just got the 5.1 lolipop update.
I almost bought 2...if I hadn't just bought the walbro 450 and abs system i would have.
I almost bought 2...if I hadn't just bought the walbro 450 and abs system i would have.
Reply
0
0
10-10-2015, 10:33 PM
#4535
Elite Member
Join Date: Mar 2007
Location: Santa Clara, CA
Posts: 5,165
Total Cats: 855
Sender:
M3031-000005-100PG Measurement Specialties | Mouser
As for hooking it in, I stuck a male/male/female tee into the AN lines and ran a remote line to it. NPT to AN male adapter from Summit, and clamp the sender to the fender. I have it hooked to the unused "EGO2" input on my MS3.
--Ian
M3031-000005-100PG Measurement Specialties | Mouser
As for hooking it in, I stuck a male/male/female tee into the AN lines and ran a remote line to it. NPT to AN male adapter from Summit, and clamp the sender to the fender. I have it hooked to the unused "EGO2" input on my MS3.
--Ian
Reply
0
0
10-11-2015, 04:06 PM
#4536
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Also need to find a 1/8npt oil pressure sensor. I need to do some testing but the plan is to set a trigger to basically shut the engine off when oil pressure goes below a certain PSI.
Reply
0
0
