astroboy

iTrader: (18)

Thanks! My list o things to do is still growing but at a much slower rate. I need to:
get the coolant outlet modified
find a plug for the oil pump
tq the exhaust manifold
get seals for the injectors
put engine and transmission in
wire up the engine
bolt everything else back on
make it work

Not so bad

Cspence

iTrader: (11)

Looks good!

astroboy

iTrader: (18)

Thanks man. I just realized I need some sort of a fpr for the mtuned fuel rail so once I can get that taken care of I should be good to go.

astroboy

iTrader: (18)

So I have accumulated everything I need to finish but missed the finish date by a large amount. On the plus side we got the bun out of the oven. Now that we are in the groove of being parents I am going to start on finishing the car. Pics of said progress

hornetball

iTrader: (4)

Well, well, well!! Congratulations, DAD!

Faeflora

iTrader: (2)

Flickr Fail. I can't see ****.

Use imgur ftw!

astroboy

iTrader: (18)

Fixed! On a down note we went to put the engine in and couldn't find the flywheel bolts so we put the engine in place so I can finish the wiring...going to have pics tomorrow.

astroboy

iTrader: (18)

Got some things on to see where I am going to place this amphenol. Need to put in the coolant reroute and then I will be sure where this thing is going. Here how the bay is looking now (I keep thinking the engine is too far forward but it's on the mounts...maybe it's just me):

Cspence

iTrader: (11)

Looks good nice and empty!

Faeflora

iTrader: (2)

Looks good.

Why the heat shield on the firewall?

astroboy

iTrader: (18)

Looks pretty? Also it was relatively inexpensive jives with the hood:



I don't think it will do **** for my comfort but the leftover material will be used on/in the tunnel.

absRTP

iTrader: (12)

-

astroboy

iTrader: (18)

Thanks mang

No pics for this update yet. Sunday we finished installing the clutch, flywheel, and 6 speed plus the engine is mounted. The injectors have their appropriate rubber and are mounted. I also targeted where the amphenol (which is going to be under the heater core lines) and am actually going to start wiring the engine. I also forgot that I have an oil temp sensor so I am going to have to install it the hard way :(

Now I need to find a manual speedo gear for the 6 speed (4.1 for now), get vacuum lines with firesleeves, get one longer water line, get the valve cover modified, wire up the engine, and install everything else.

Faeflora

iTrader: (2)

astroboy

iTrader: (18)

The clicky thing doesn't work! WTFFFFFFFFFFFFFFFFFFFFFFFFF!

Faeflora

iTrader: (2)

ok i fixed it !!! <3

astroboy

iTrader: (18)

STill trying to figure out where this amphenol is going and fucked around with some paint.



Too faeflora?


Thinking about putting the amphenol over the colant line to the right side. Input?


Purple turbo makes me lol

charlie_91

such a sick bay.. where did u get ur cam gears ? every place ive emailed said there out of stock..

baron340

iTrader: (5)

Build is looking great so far. One little detail though... you might want to reconsider using Super Blue brake fluid. It works well and the boiling point is pretty high, but it will stain every single thing it touches blue forever. We usually use Motul RBF 600 or 660 at work, nice high boiling point and doesn't stain every damn thing blue.

Other than that, it looks fabulous. I'm impressed with the whole brake reroute.

Faeflora

iTrader: (2)

Try flyin miata. They actually have a group bu on em now.