The engine bay? That is the color. It's not primer. I'd say more of a flat black, but more grey-ish. I want the focus to be more on the engine, thus the lack of color. Plus I'm not going lime green or pink.
Haha oh yes the 7 IC setup. What a horrific turn of events. Glad that is in the past. I can assure you this setup will be 180 degrees different. Ryan, the bumpers and hood were ruined in a botched IC setup. The fender and door were used on a different miata, which at the time that I sold it, I didn't think I was going to revive this project. Moar pics from this weekend later. |
3 Attachment(s)
Mounting spot for the MS. It will be insulated when it is actually installed.
https://www.miataturbo.net/attachmen...ine=1314721215 Early stages of the harness. This is just the MS to engine stuff part. https://www.miataturbo.net/attachmen...ine=1314721215 Getting an idea of wtf goes where. https://www.miataturbo.net/attachmen...ine=1314721215 |
I've always wanted to tackle mine like this...but am not a masochist like you.
Good luck...looking good. |
It's actually going together easier than expected.
|
Is that a 1.6 or 1.8 crankshaft? The one I see out way in the back of the garage.
Give it a good coating of grease or something ( and maybe wrap it in plastic), the last thing you want is rust in those journals. That is of course if it is in good condition. Why does the oil pan has two plugs side by side? and like always JB weld, lets hope it does not leak. |
1.8 crank, it's junk. Might make something cool out of it one day.
Oil pan was for a twin turbo build back in the day. Holes were drilled/tapped/sealed, then JB weld over them. |
4 Attachment(s)
Cleaned a bit today since an S10 will be in there for the next 2 weeks as I do some work for a buddy.
https://www.miataturbo.net/attachmen...ine=1314822062 Block off plates and the injector harness. https://www.miataturbo.net/attachmen...ine=1314822062 Going to modify the relay/fuse box, and it will be located in the engine compartment. https://www.miataturbo.net/attachmen...ine=1314822062 MOAR wires are appearing https://www.miataturbo.net/attachmen...ine=1314822062 https://www.miataturbo.net/attachmen...ine=1314822062 |
You do work!
Looks good |
Honestly this build has been a lot of fun. It's great just going to the shop, working until I don't feel like, then leaving. No deadline, no frustration, just fun. Although I do have a goal of getting it on the road by the end of October. But if I don't reach that, oh well.
|
Now not only am I doing this in a storage unit... but this POS is parked in front of it...
http://www.miataforumz.com/attachmen...ine=1314905628 Got some stuff done before that though.. http://www.miataforumz.com/attachmen...ine=1314905628 http://www.miataforumz.com/attachmen...ine=1314905628 http://www.miataforumz.com/attachmen...ine=1314905628 Basically all engine sensor wiring has been run, now I need to solder/shrink to connector and I'm DONE with engine wiring. Still need to tuck/protect it after that, but won't be doing that until I know the wiring is good :D I know I"m going to get a face full of haterade when I mention this... but headlights will be fixed in the up position.. yea yea aerodynamics, it looks ugly, blah blah blah... I like it FFFFUUUUUUUUUUU |
Just ordered a massive amount of small shit to help get my car moving forward. Sadly (not really) I've already reserved this weekend for shenanigans, so not much will get done. I have to finish up the S10 on Sunday, and Monday depending on how long it takes to do everything. So who knows.
|
1 Attachment(s)
|
3 Attachment(s)
Fuck I'm so lonely in this thread. I know I don't have shiny shit, but the man hours invested could be considered slave labor.
Not perfect, but simple. Only what is needed is there. I added two extra wires for my oil temp and eventual EGT stuffs. https://www.miataturbo.net/attachmen...ine=1316313051 I know they are on the exhaust side. Not too worried as there will be some heat shielding on the exhaust. I may flip them, but need to get this B running. https://www.miataturbo.net/attachmen...ine=1316313051 Coming together. Once I get the diff installed, and put the subframe back, all I need to do is hook up the driveline and battery and it should ruN! https://www.miataturbo.net/attachmen...ine=1316313051 Once it's running I still have a ton to do. But getting it running will be a huge step forward. |
Another harness from scratch ... nice.
Every thread like this makes me want to ball up and do the same - until I pull out the diagrams and start realizing the man hours involved. I wish, like the Honduh boys, we had a vendor who sold 'stripped' harnesses. -Zach |
Shit just got real.
http://www.miataforumz.com/attachmen...ine=1316379107 http://www.miataforumz.com/attachmen...ine=1316379107 http://www.miataforumz.com/attachmen...ine=1316379107 http://www.miataforumz.com/attachmen...ine=1316379107 http://www.miataforumz.com/attachmen...ine=1316379107 http://img12.imageshack.us/img12/3139/photo8wg.jpg Tach will go in the middle. Have not decided where my speeedo will go. The two empty spots will soon be coolant temp and EGT. And by soon.. I mean after it's running. Panel on the right will house my Ignition switch and push start. As well as accessory switch. Probably lights and turn signal (turn signals will go down by the shifter so it will be easy to reach... thinking about doing a time delay type deal with just a button... press it and the signal goes on for 20-30 seconds. Might get annoying at left turn lanes at stop lights.) |
I've got some pictures of the dash mounted in the car with some of the gauges. Looks pretty damn good IMO. I still need to add some bracing to make sure it doesn't vibrate too much. But I need to find a dash bar first. I just got in my tach mount today, so I can mount the tach on the dash. My water temp gauge will be in any day.
Dial indicator and Mic should be in today, I'll set backlash and preload this weekend, install the new mounts, and get the subframe in. Also hoping to pull the engine, install clutch + flywheel, attach trans and get the whole drive line in this weekend as well. That means MAYBE a running miata by Monday. That is assuming my second hand MS works as advertised. New steering wheel should be in, as well as my ebay quick release/mount. |
very cool, I was contemplating of just using the crossbar at one point alone for all my gauges.
Are you going to run a stripped interior? I am assuming so. |
2 Attachment(s)
Tach obviously still needs to be mounted. And only 3 of the gauges are there, but you get the idea.
https://www.miataturbo.net/attachmen...ine=1316792417 https://www.miataturbo.net/attachmen...ine=1316792417 Yes the interior will be 90% stripped. |
2 Attachment(s)
Shit moved slow today. But I did reach a big milestone. For the first time in over a year I have a rolling chassis... with both subframes attached.
Here are a few pics of the diff going back in... so much easier to install with the subframe out lul https://www.miataturbo.net/attachmen...ine=1316913294 https://www.miataturbo.net/attachmen...ine=1316913294 Moar pics tomorrow after I get some stuff done. Don't mind my messy gasket job :D |
All times are GMT -4. The time now is 08:49 PM. |
© 2024 MH Sub I, LLC dba Internet Brands