Faelflora breaks his promise, time to part out car. GIT THE SAWZALL!
06-04-2012, 02:38 AM
#2882
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
d
a
fukk are you talking baout
are you sqaying this is a bad idea?
i have to get this ----- out of my car. it will happen. trust me. i was not jocking about the sawzall;
Reply
0
0
06-04-2012, 08:38 AM
#2885
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,646
Total Cats: 3,009
When the slave reaches the end of its ability to help at the end of its stroke a little fluid will go into its dust boot. NBD. I'd say a little fluid spill is the least of his concerns at present.
Fae, there is one more thing that might be holding it up. Did you remove the PPF?
Fae, there is one more thing that might be holding it up. Did you remove the PPF?
Reply
0
0
06-04-2012, 08:53 AM
#2886
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
When the slave reaches the end of its ability to help at the end of its stroke a little fluid will go into its dust boot. NBD. I'd say a little fluid spill is the least of his concerns at present.
Fae, there is one more thing that might be holding it up. Did you remove the PPF?
Fae, there is one more thing that might be holding it up. Did you remove the PPF?
Good idea let me make sure it is not resisting
Reply
0
0
06-04-2012, 01:32 PM
#2890
Elite Member
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
"by February 2011 over 900,000 MX-5s had been built and sold around the world.[2]"
Reply
0
0
06-04-2012, 02:35 PM
#2892
Fae, I will race you, I need to pull the tranny from my f prod miata the quafie does not have a drain plug so I need to pull it to drain the gear box, talk about poor design. Anyway I plan to start the project in a couple of hours, I bet I'm done 1st. Glad your back bro, the entertainment value of this threshing us priceless.
Reply
0
0
06-04-2012, 02:47 PM
#2895
http://www.miata.net/faq/production.html
According to the old guys at M.net, Mazda sold ~300k Miatas in the US market. None of this is in ANY way relevant to whether or not Fael has the ability to come up with new and inventive ways to screw up his car.
According to the old guys at M.net, Mazda sold ~300k Miatas in the US market. None of this is in ANY way relevant to whether or not Fael has the ability to come up with new and inventive ways to screw up his car.
Reply
0
0
06-04-2012, 10:40 PM
#2898
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Struggled with this mothrfukker for a few more hours tonight.
WHAT THE FUKK WHY
I ripped off the shift fork bootie and sprayed a can of kroil in there. didn't do jack.
BTW the shift fork freely slides around. then again, the transmission is about 3/4" away from the oil pan. i should have pulled the motor to get this out. i am mangling the shiz out of my oil pan. that is not good.
for the record the transmission CAN wiggle around at various angles. the input shaft is probably still in the outmost disc though. the PPF is not an obstruction.
My bar is about 3 feet long and judging by prior use of my torque wrench, I'm exerting over 200ft/lbs on this case.
Maybe if I pry both sides at the same time. Anyone want to come fucky my tranny out of my car with me?
If I fail to get this out by wednesday this is going to happen. i'm serious
WHAT THE FUKK WHY
I ripped off the shift fork bootie and sprayed a can of kroil in there. didn't do jack.
BTW the shift fork freely slides around. then again, the transmission is about 3/4" away from the oil pan. i should have pulled the motor to get this out. i am mangling the shiz out of my oil pan. that is not good.
for the record the transmission CAN wiggle around at various angles. the input shaft is probably still in the outmost disc though. the PPF is not an obstruction.
My bar is about 3 feet long and judging by prior use of my torque wrench, I'm exerting over 200ft/lbs on this case.
Maybe if I pry both sides at the same time. Anyone want to come fucky my tranny out of my car with me?
If I fail to get this out by wednesday this is going to happen. i'm serious
Reply
0
0
