If it's just "overspray," should clean it up pretty easily with sandpaper or a wire brush. It may not be enough to really worry about. Dunno.
|
Maybe the turbo will just eat whatever flakes come off and smile?
I'm getting to the point where I will probably just say fuck it and run the thing. If it blows up due to residue then I can always source a cheap turbo or just throw everything away and buy a Corvette. I'm almost 40 as it is. Also, this stuff is really tough. I was test fitting and banged it against a few things in there and it didn't leave a mark. |
Good point, i mean it is just a greddy turbo. If it were my gt2860rs i would be scared of scrapping the turbo though.
Just chip at it with a wire brush/tools and see if you can remove it. If you cant easily remove it, and it doesn't seem to flake easily, run it. |
The guy reiterated to me that he has never had an issue with the material coming off, which is why he would have done the interior of the manifold if I had asked. My admittedly unscientific test of banging it on the engine block by accident seems to show that it's pretty durable.
|
Nice to see it coming together Harv. I wish I was at your point in my build!
|
Originally Posted by Jeffbucc
(Post 1071215)
Nice to see it coming together Harv. I wish I was at your point in my build!
:bowrofl: |
Originally Posted by Harv
(Post 1071221)
Ha ha ha, come on, if you saw my car you would have taken it all apart and cleaned out all the dirt and crud, swapped the motor back after giving it a shiny paint job and then put it back together again in the time I took to remove the manifold. :bowrofl: |
Another Greddy kit in SW CT, fun! That turbo is unworthy of that manifold. :)
|
Nothing is ever easy.
Got the manifold installed, still need to figure out an intake piping setup now that the airbox is gone, but while I was thinking about that I decided to swap in the new injectors. Mind you I have had this fuel rail off before so I wasn't expecting problems, but it turns out one of the bolts seized up and broke off. Sooo, once the small amount of fuel that leaked out dries up I'll drill that out and hopefully the threads will be okay and I can just get another bolt. Also managed to break a clip off one of the fuel injector connectors. :vash: |
I think that almost all of my fuel injector clips are broken and have been for 20-30K miles. LOL. Maybe I'll fix them one day, but it doesn't cause problems.
|
Friend came over with some stuff and helped me drill the hole out and retap it. Seems to be okay now. Did you know that 14 lb/ft is not a lot of torque?
|
Yeah I'm always surprised at how little it is. For some reason whenever I get a torque wrench in my hands I always think I need to make a herculean effort on the first pull.
|
I see noobs abusing torque wrenches all the time out at the track. They literally jump on them with everything they have when they retorque their lugs. Did it click? Hell yeah, it clicked -- but you have no idea how much torque you just applied.
Please, use them correctly, gradually increasing pressure until you get the click. Finesse, like the throttle on track out or a third date. |
Yeah, pretty sure when I tightened up the injector rail last time I just blew it on the amount of torque needed as the specs are 14-19lbs for those and that's not a lot and I didn't use a torque wrench. BTW, having the full service manual for the Miata is very useful. I got a used one for $50.
Oh and I hooked up the MS3 and it actually connected and is reading my VTPS. Gonna wait to start until I hook up the WBO2. Just need to verify with Scott that the middle connector is where he put the O2 wire and I'll wire it in. I've got the LC1 connected to the gauge in the interior right now, I'm assuming that splicing off the wiring going into that and running it over to the MS isn't going to present a problem. I'd take some pics of the car back together, but other than the manifold it looks as horrible as it ever has and my wiring for the AIT sensor is terrible as well since the amount of wire they give you isn't that much for running from the intercooler. Where do people run the wiring for the AIT? I just ran it up from the IC in back of the radiator and over to the AFM connector. |
Originally Posted by hornetball
(Post 1071928)
Please, use them correctly, gradually increasing pressure until you get the click. Finesse, like the throttle on track out or a third date. |
Hell, I just realized I have to go through the wiring and figure out where I had connected the Bipes into the the harness and remove it.
|
Originally Posted by Harv
(Post 1071932)
BTW, having the full service manual for the Miata is very useful. I got a used one for $50.
Originally Posted by Harv
(Post 1071932)
I'm assuming that splicing off the wiring going into that and running it over to the MS isn't going to present a problem.
Originally Posted by Harv
(Post 1071932)
my wiring for the AIT sensor is terrible as well since the amount of wire they give you isn't that much for running from the intercooler.
The wire that comes with the kit is high-quality though.
Originally Posted by Jeffbucc
(Post 1071975)
If you haven't sealed the deal by the second date you need practice son!:rofl:
|
Originally Posted by hornetball
(Post 1072136)
I'm old fashioned. Plus, given the incredeble car progress in your build thread, not sure you've got room to talk. How long has it been? :rofl: |
Originally Posted by hornetball
(Post 1072136)
FSM's are on this site as stickies. Easily downloaded.
|
1 Attachment(s)
https://www.miataturbo.net/attachmen...ine=1384198358
I'm trying to puzzle out the intake situation. My problem is that there are obstacles in the way, not the least of which is that intercooler piping that goes up and over the PS/AC stuff. The other annoying thing is that the adjustment screw for the shock sticks up out of the tower about two or three or so inches so going up and over it and into the corner is a pain. I decided I would try ordering this and see if I can just fit the thing right in front with a slight bend downward to clear the IC pipe. Now I just need a cone filter with a 2.5 inch opening. cxracing.com: 2.5" OD Intercooler Aluminum 45 Degree Pipe Kit + Hose + 2 Clamps |
All times are GMT -4. The time now is 05:52 AM. |
© 2024 MH Sub I, LLC dba Internet Brands