HOUSE CAT
11-30-2015, 02:30 AM
#101
Elite Member
Thread Starter
iTrader: (2)
Join Date: Dec 2011
Location: SoCal
Posts: 2,447
Total Cats: 478
Extended LBJ Group Buy
BTW, I just put a small group buy up in the classifieds section for the extended lower ball joints. My hope is that those who are going to put them on their car NOW will get them, test them, and then give feedback.
Only "some" will be coming by air--hopefully 10 pair--and will dole those out based on the group buy list. Many more are on the way.
Last, we've had some good initial response from a sanctioning body for use on the track. Fingers crossed.
Only "some" will be coming by air--hopefully 10 pair--and will dole those out based on the group buy list. Many more are on the way.
Last, we've had some good initial response from a sanctioning body for use on the track. Fingers crossed.
Reply
0
0
12-11-2015, 12:33 AM
#102
Elite Member
Thread Starter
iTrader: (2)
Join Date: Dec 2011
Location: SoCal
Posts: 2,447
Total Cats: 478
Engine Test Fit
The House Cat got a test engine fit tonight, and it's looking pretty good. It was a little stressful because the V8R K member and the engine mount brackets are both custom, and this is the first time with the engine in the car. It turns out that a slight amount of "massaging" will need to be done, but otherwise it's all good.
It fits, but needs a slight tweak before it's permanent.
The engine was moved back a bit in the frame.
Might need to get creative with the coolant reroute.
Reply
0
0
12-11-2015, 01:22 AM
#103
SADFab Destructive Testing Engineer
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
The House Cat got a test engine fit tonight, and it's looking pretty good. It was a little stressful because the V8R K member and the engine mount brackets are both custom, and this is the first time with the engine in the car. It turns out that a slight amount of "massaging" will need to be done, but otherwise it's all good.
It fits, but needs a slight tweak before it's permanent.
The engine was moved back a bit in the frame.
Might need to get creative with the coolant reroute.
Reply
0
0
01-19-2016, 06:50 PM
#106
Elite Member
Thread Starter
iTrader: (2)
Join Date: Dec 2011
Location: SoCal
Posts: 2,447
Total Cats: 478
I'm sure most of you have seen or done this before, but I went to Home Depot and bought some 3M traction tape (grip stop) for my pedals. Busted rubber comes off, tape goes on. A big patch is easier to razor blade off than a small one, and then finishing is easy with a file. Add Sharpie to hide bare metal. No, these aren't Tilton or Wilwood, but they give good feel. I add four stainless hex button head screws to the bottom holes of the gas pedal for a little extra grip too.
Home Depot 3M grip tape.
Goes on quick
Bigger pieces razor off easier than smaller.
File the edges.
Sharpie hides bare metal.
Home Depot 3M grip tape.
Goes on quick
Bigger pieces razor off easier than smaller.
File the edges.
Sharpie hides bare metal.
Reply
1
1
01-19-2016, 10:10 PM
#107
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,015
Total Cats: 6,587
I used a similar product also from Home Depot. Didn't see the grip tape you refer to, mine was a flat, wide strip that is intended for applying to a stair step. Same basic idea, though.
Highly recommended, even if you have normal size feet. It's a massive improvement, particularly when your shoes are wet. Yes, I realize this isn't something Cord ever has to deal with in north San Diego county, but for the rest of us...
Reply
0
0
01-19-2016, 10:17 PM
#108
Elite Member
Thread Starter
iTrader: (2)
Join Date: Dec 2011
Location: SoCal
Posts: 2,447
Total Cats: 478
Never did it for the brake pedal (I like being able to slip a bit on it for heel-toe), but I've given that exact treatment to the clutch pedal on all three of my Miatas. When you wear a size 14 boot, removing the rubber pad from the clutch pedal is literally the only way to get past it onto the dead pedal.
I used a similar product also from Home Depot. Didn't see the grip tape you refer to, mine was a flat, wide strip that is intended for applying to a stair step. Same basic idea, though.
Highly recommended, even if you have normal size feet. It's a massive improvement, particularly when your shoes are wet. Yes, I realize this isn't something Cord ever has to deal with in north San Diego county, but for the rest of us...
I used a similar product also from Home Depot. Didn't see the grip tape you refer to, mine was a flat, wide strip that is intended for applying to a stair step. Same basic idea, though.
Highly recommended, even if you have normal size feet. It's a massive improvement, particularly when your shoes are wet. Yes, I realize this isn't something Cord ever has to deal with in north San Diego county, but for the rest of us...
Reply
0
0
01-20-2016, 07:06 AM
#109
I just went to the local skateboard shop and asked for a scrap piece of grip tape. They had tons of it. All sorts of color and designs. A tip next time you apply it (comes from years skateboarding), apply it and then round the edges with a round metal object, I use a screwdriver. This will perforate the edge after a few round on it and you can just pop the access right off with some pressure. It makes for a very clean edge.
Reply
0
0
01-21-2016, 12:12 AM
#110
Elite Member
Thread Starter
iTrader: (2)
Join Date: Dec 2011
Location: SoCal
Posts: 2,447
Total Cats: 478
I just went to the local skateboard shop and asked for a scrap piece of grip tape. They had tons of it. All sorts of color and designs. A tip next time you apply it (comes from years skateboarding), apply it and then round the edges with a round metal object, I use a screwdriver. This will perforate the edge after a few round on it and you can just pop the access right off with some pressure. It makes for a very clean edge.
Reply
0
0
01-21-2016, 12:25 AM
#111
Elite Member
Thread Starter
iTrader: (2)
Join Date: Dec 2011
Location: SoCal
Posts: 2,447
Total Cats: 478
I'm trying some new things with the House Cat. Some of that includes adding weight, but also adding a bit of refinement. This car will be more road-focused, so it needs to look the part.
The pictures are of the future aluminum front splash guards, and the rear trunk section, which will be made in fiberglass, and should be covered in fabric. The gas cap can be hidden with this setup.
Open the trunk and this is what you'll see. The cover hides the gas tank, and adds a small luggage area. Yes, hinge.
I'm toying with the idea of putting the gas cap under the trunk so it stays out of view.
This simple template is the front fender splash guard. It separates the tires fronts from the engine bay and helps direct air.
Can't wait to see this in laser-cut aluminum.
The pictures are of the future aluminum front splash guards, and the rear trunk section, which will be made in fiberglass, and should be covered in fabric. The gas cap can be hidden with this setup.
Open the trunk and this is what you'll see. The cover hides the gas tank, and adds a small luggage area. Yes, hinge.
I'm toying with the idea of putting the gas cap under the trunk so it stays out of view.
This simple template is the front fender splash guard. It separates the tires fronts from the engine bay and helps direct air.
Can't wait to see this in laser-cut aluminum.
Reply
0
0
01-21-2016, 01:02 PM
#118
My car is currently up on jacks without an exhaust on a frozen mud driveway covered in snow. I am so sad; I had studded tires ready to go.
Someday I will have a catfish, I've been dreaming of this car ever since I first saw it. It's been decided, when living situations change. (Hiring btw?)
Someday I will have a catfish, I've been dreaming of this car ever since I first saw it. It's been decided, when living situations change. (Hiring btw?)
Reply
0
0
