|
NB Artech
8 Attachment(s)
Recent Artech acquisition. Really nice quality - too pretty not to post. A little worried about how loud the dump will be.
https://www.miataturbo.net/attachmen...ine=1398127285 https://www.miataturbo.net/attachmen...ine=1398127285 https://www.miataturbo.net/attachmen...ine=1398127285 https://www.miataturbo.net/attachmen...ine=1398127285 |
Dont sweat the dump tube. Its only loud when you want it to be loud.
If you find that its opening up to often, then you just need to turn the boost up. :party: |
I saw that on CR and was thinking about it except that I have a T25 Disco and this is a T3. Good find.
Who's run a "screamer pipe" and how bad is it really ? |
I have one on my daily driver mitsubishi galant, unless you've hit full boost its really not any louder.
|
8 Attachment(s)
Parts are starting to trickle in. Anybody know what the bolt that secures the dump tube in the last pic is used for? It's ~6" long
https://www.miataturbo.net/attachmen...ine=1399598579 https://www.miataturbo.net/attachmen...ine=1399598579 https://www.miataturbo.net/attachmen...ine=1399598579 https://www.miataturbo.net/attachmen...ine=1399598579 |
12 Attachment(s)
Pretty much complete with "stage 1" - 5psi EWG spring. Only issue so far is the minimal clearance between down pipe and steering shaft.
Glowshift oil plate, 48" Aeroquip -3an oil feed, no restrictor https://www.miataturbo.net/attachmen...ine=1399759222 https://www.miataturbo.net/attachmen...ine=1399759222 -10an oil drain. Still need a -8 to -10an fitting https://www.miataturbo.net/attachmen...ine=1399759222 https://www.miataturbo.net/attachmen...ine=1399759222 2-1/4" piping. Not sure if I will intercool or go with water injection. https://www.miataturbo.net/attachmen...ine=1399759222 https://www.miataturbo.net/attachmen...ine=1399759222 |
awesome setup. How much did the turbo manifold, ewg, down pipe, and dump tube run ya? its all from artech correct?
|
very nice.
that 6" bolt is holding the oil pan |
Originally Posted by 97miatanola
(Post 1129967)
awesome setup. How much did the turbo manifold, ewg, down pipe, and dump tube run ya? its all from artech correct?
Originally Posted by 18psi
(Post 1129975)
very nice.
that 6" bolt is holding the oil pan |
10 Attachment(s)
... and done for now (except for some heat protection). The only real issue with the install was the down pipe interference. I didn't want to bang on it but it was the easiest solution and didn't need much shaping. Also had to source a 3" exhaust gasket online.
EWG sounds pretty cool. Running sans BOV is a little irritating though. https://www.miataturbo.net/attachmen...ine=1400354808 https://www.miataturbo.net/attachmen...ine=1400354808 https://www.miataturbo.net/attachmen...ine=1400354808 https://www.miataturbo.net/attachmen...ine=1400354808 https://www.miataturbo.net/attachmen...ine=1400354808 |
8 Attachment(s)
Hood got extremely hot above the turbo. Added a "Thermal Zero" (T3 small) turbo blanket and thermotec wrap for the heater hose. Blanket works great for reducing temps - hopefully it holds up.
https://www.miataturbo.net/attachmen...ine=1400800679 https://www.miataturbo.net/attachmen...ine=1400800679 https://www.miataturbo.net/attachmen...ine=1400800679 https://www.miataturbo.net/attachmen...ine=1400800679 |
8 Attachment(s)
Type 10 BOV from siliconeintakes.com - works fine.
https://www.miataturbo.net/attachmen...ine=1400898383 https://www.miataturbo.net/attachmen...ine=1400898383 https://www.miataturbo.net/attachmen...ine=1400898383 https://www.miataturbo.net/attachmen...ine=1400898383 |
6 Attachment(s)
Cold air box and small heat shield added.
https://www.miataturbo.net/attachmen...ine=1401638595 https://www.miataturbo.net/attachmen...ine=1401638595 https://www.miataturbo.net/attachmen...ine=1401638595 |
You're ruining the flow of that coupler with the pipe. There's gotta be a better way.
I have the same coupler clamped to my inter cooler, with a 90* pipe clamped to the other side, going around the radiator. Keep that in mind for when you ditch your silly water injection dreams. |
1 Attachment(s)
Wow can't believe you are running this setup without an intercooler! Get an intercooler on there lol
I have the same manifold and can't wait to get it set-up in the car! Probably wont be until August though :sad2: https://www.miataturbo.net/attachmen...ine=1401642330 |
I was hoping the cold air box would be more effective at reducing intake temps. On a 90deg day, seeing ~175F during 7psi 2nd-4th run through the gears. No pinging but yeah, intercooler is on the list.
|
18 Attachment(s)
MSM I/C and piping
Some convenient tapped holes for mounting. https://www.miataturbo.net/attachmen...ine=1405777541 https://www.miataturbo.net/attachmen...ine=1405777541 https://www.miataturbo.net/attachmen...ine=1405777541 Upper radiator hose needs to be shortened. https://www.miataturbo.net/attachmen...ine=1405777541 MSM cold side pipe fits without modification. https://www.miataturbo.net/attachmen...ine=1405777541 Straight 2.25" al. tube used to connect to intake and for mtg of iat and bov. https://www.miataturbo.net/attachmen...ine=1405777541 Hot side piping. MSM piping can be used with some modifications. https://www.miataturbo.net/attachmen...ine=1405777541 https://www.miataturbo.net/attachmen...ine=1405777541 Thought I was done - not enough clearance between oil drain and turbo outlet to install coupler. :vash: https://www.miataturbo.net/attachmen...ine=1405777541 |
I think the BOV should be as close to the intake as possible. Also your radiator looks a bit brown.
Really like the cold air box. |
10 Attachment(s)
Finished up hot side piping. I think I'm done ...
https://www.miataturbo.net/attachmen...ine=1406394624 https://www.miataturbo.net/attachmen...ine=1406394624 https://www.miataturbo.net/attachmen...ine=1406394624 https://www.miataturbo.net/attachmen...ine=1406394624 https://www.miataturbo.net/attachmen...ine=1406394624 |
Artech... and an MSM intercooler??
|
| All times are GMT -4. The time now is 04:52 AM. |
© 2024 MH Sub I, LLC dba Internet Brands