|
The main reason I want to keep it noninterference is the cams spring toward each other on the compression stroke causing the belt to slacken between the cam gears which looks like it will cause shock load and compromise the belt. I started a thread with more info in the "engine performance" section.
I have a new gates RPM blue timing belt. From my experience with this motor and previously on my B6T I have thrown a few timing belts and don't want to blow up an engine that has taken 2 years and almost 10k to build. |
9 Attachment(s)
Angle plate got here early. Made some soft jaws by annealing some copper plumbing couplers so my toe clamps cant mar the pistons. Had to open the slots in the base cause they're 12mm and not 1/2". Broke a tap making new T-slot nuts out of some grade 10.9 bolts. Luckily the tap broke high enough to grind it back and tap a second one. Got a test piston cut. Gonna clamp up the Wisecos tomorrow and hopefully they come out as nice.
Attachment 231185 Attachment 231186 Attachment 231187 Attachment 231188 Attachment 231189 Attachment 231190 Attachment 231191 Attachment 231192 Attachment 231193 |
4 Attachment(s)
Finished machining the pistons and started the final assembly. More issues with the head I bought, they only cut one gear to make it adjustable. Luckily, I have a lathe at work and was able to cut it but it's still very frustrating. With the head torqued I reconfirmed that it is a non-interference engine. I needed to know that the pistons 100% can't touch the valves just in case something goes wrong. I made a new CAS extender to fit the FE5A camshaft. Had to reduce the diameter of the offset wing piece without touching the wings which was pretty sketchy operation then machined down a lug bolt to make up the extra 30mm pin to pin distance.
Attachment 231181 Attachment 231182 Attachment 231183 Attachment 231184 |
7 Attachment(s)
Pulled the wrap off to re-rap it and found my #1 runner split in half. welded it back together and found the exhaust flange badly warped. No machine shops would put it on their belt grinder so I spent 4 hours with a surface plate and 80 grit sandpaper to get it to within .005" of flatness.
Attachment 231174 Attachment 231175 Attachment 231176 Attachment 231177 Attachment 231178 Attachment 231179 Attachment 231180 |
9 Attachment(s)
Hopefully this is the last finishing touches on my mustang 2 front end. Turns out my upper control arm height was an inch high, and the lower edge of my cross member was an inch low. Proper suspension geometry and ground clearance has been restored. I just need to do more clean up, shoot some paint on it so it doesn't rust and finish the final touches on the motor so I can drop it in.
Attachment 231165 Attachment 231166 Attachment 231167 Attachment 231168 Attachment 231169 Attachment 231170 Attachment 231171 Attachment 231172 Attachment 231173 |
What a cool build. I love it
If you ever need laser cut parts, including turbing, check out Captial Metal Works. Kris is a Datsun buddy of mine and has helped me a ton. He's also in Sacramento area |
Thanks! I'll keep him in mind if I need something.
It's alive!!!!! |
Glad to see it! Sounds smooth! Ready for the sauce!
|
13 Attachment(s)
Tying up all the loose ends. Condenser is mounted, oversized slave from a 86 4Runner SR5 installed. There is a massive improvement going to a 13/16 master vs the stock 3/4 master. Brake hydraulics are all finished and leak free. I've been driving it for the last few days with my shop floor alignment using a toe bar, tape measure, and a digital angle finder to set camber. I need to get 500 miles on it to break it in before final tuning.
Attachment 231152 Attachment 231153 Attachment 231154 Attachment 231155 Attachment 231156 Attachment 231157 Attachment 231158 Attachment 231159 Attachment 231160 Attachment 231161 Attachment 231162 Attachment 231163 Attachment 231164 |
9 Attachment(s)
More progress. The 94-99 DeVille tails looked a bit thick on the bottom so I found a set of 89-93s. Not 100% sure which ones I'm going with at the moment but ill have the buckets from Grant Fab this week. I'm leaning towards the taller, thinner 89-93s cause the contour is pretty much perfect.
Attachment 231143 Attachment 231144 Attachment 231145 Attachment 231146 I finished the A/C hard lines and should have the hoses and fittings to finish everything this week. I routed the low side from the expansion valve down and looped it back forward so I could braze the high side line that goes into the expansion valve to it to assist with cooling the refrigerant a little more. all newer cars do this by putting the high side line inside the low side line so I figured it might help. Attachment 231147 Attachment 231148 Attachment 231149 Attachment 231150 I swapped out the louvered hod for the smooth one. I like the smooth look better and im hoping the louvers will not be necessary with the condenser under the bed. Attachment 231151 |
11 Attachment(s)
Finishing up the A/C so I thought I'd make it more fun to drive. Made a tight slip fit arbor, cut down the old flywheel and made a weight for the new aluminum one. 6lbs was way too light. Added 12lbs to the flywheel. Clutch and flywheel together weigh in at 25.8lbs which is still 5-7lbs lighter than stock. It took around 16 hours to make. Such a pain but I'm hoping it will be more pleasant to drive and be able to idle under 1000rpms now.
Attachment 231132 Attachment 231133 Attachment 231134 Attachment 231135 Attachment 231136 Attachment 231137 Attachment 231138 Attachment 231139 Attachment 231140 Attachment 231141 Attachment 231142 |
4 Attachment(s)
UPDATE: Flywheel is balanced, took it for a drive then the turbo blew, dropped the turbo off to get built and got a cheapo housing and machined a piston to press into the center section so I could drive it NA and get the alignment done. Then I wrecked my Harley. I can't work on anything for a few weeks until my ribs and collar bone heal. Hopefully my turbo gets finished soon so it's waiting for install it as I heal up.
Attachment 231128 Attachment 231129 Attachment 231130 Attachment 231131 |
Piston into turbo to drive n/a :laugh: you literally never cease to amuse me :likecat:
Sucks about the fall, hope you recover quickly, it's race weather my friend. |
Sorry to hear about the fall, hope you heal quickly and easily! Hope to meet you at Sacramento raceway some time soon too
|
After looking at so many different ways to get the alignment heads to clear without hitting my fenders it dawned on me to just put the skinnier wheels on that leave tons of room. I feel stupid when the solutions are so simple. Alignment is done. Found the source of my a/c leak, it was coming from the base of an r12 filter that I'm using as an accumulator for my cycling switch. sealed the threads and I don't see any further leaks yet. Thanks to my awesome turbo block off piston, I've been able to drive it around to get all the little things taken care of so it's ready to go when the turbo comes back. Fuel tank is painted black, the silver one has been bugging me for quite some time.
https://i.imgur.com/Mh0g7Dp.jpg https://i.imgur.com/3nPIYah.jpg https://i.imgur.com/tIWh8Kt.jpg https://i.imgur.com/1Uq4gOF.jpg https://i.imgur.com/Toe3cxz.jpg https://i.imgur.com/IBRuibX.jpg https://i.imgur.com/OYf7cev.jpg https://i.imgur.com/lK2Gotv.jpg https://i.imgur.com/bMpSu9W.jpg |
the rub marks on the flares are old when it was like 2" lower. there is plenty of clearance now.
Working on finishing up the interior, foamed up the center console. As soon as it cures i can shave it down into shape and fiberglass over it. https://i.imgur.com/lxQDAK8.jpg https://i.imgur.com/3J9xNGK.jpg https://i.imgur.com/XGH86A5.jpg https://i.imgur.com/6sTOX1H.jpg Got a message on fordfestiva.com that someone needed a hydro trans ims adapter for their build. luckily i never throw anything away and still have some of my jigs from over a decade ago. https://i.imgur.com/pgMfwRl.jpg https://i.imgur.com/deg3aV5.jpg |
Finished sanding and picked a paint, I think it turned out pretty good.
https://i.imgur.com/OWVF96T.jpg https://i.imgur.com/gdhhhv5.jpg https://i.imgur.com/8vkKwxR.jpg https://i.imgur.com/bNMvJ0s.jpg https://i.imgur.com/1uMxqpM.jpg https://i.imgur.com/bgUszy3.jpg https://i.imgur.com/NtskWAG.jpg https://i.imgur.com/LS54pp6.jpg https://i.imgur.com/6VcyoFq.jpg https://i.imgur.com/LSVI5MK.jpg https://i.imgur.com/nl9dhf3.jpg https://i.imgur.com/eYJnOdM.jpg [img]https://i.imgur.com/E5Af5Up.jpg[img] https://i.imgur.com/Elwh5fo.jpg https://i.imgur.com/c3whvqG.jpg https://i.imgur.com/NVvqq7l.jpg https://i.imgur.com/sYqlUuW.jpg |
Feeling motivated lately to get this interior finished.
https://i.imgur.com/d2ESMB6.jpg https://i.imgur.com/XuIXKZx.jpg https://i.imgur.com/CdO92JZ.jpg https://i.imgur.com/IzcPaNs.jpg https://i.imgur.com/d7pDEm1.jpg https://i.imgur.com/Q7SUJeq.jpg https://i.imgur.com/dzVUIiN.jpg https://i.imgur.com/c04pATn.jpg |
More updates on the truck. Turbo is finished and back in. The oil catch can is mounted and connected, not running a filter just a draft tube to the bottom of the truck, the drivers door panel is installed but I ran out of rivets so ill have to wait til next weekend for the passenger side.
https://i.imgur.com/yw3xVGn.jpg https://i.imgur.com/76lVR3H.jpg https://i.imgur.com/GmFjqbu.jpg https://i.imgur.com/wb1DPr6.jpg https://i.imgur.com/QWyL6Uk.jpg https://i.imgur.com/R76r05N.jpg https://i.imgur.com/YgxG8iO.jpg https://i.imgur.com/IJnsYMW.jpg https://i.imgur.com/XDFCRl6.jpg https://i.imgur.com/s1fqBMm.jpg |
More updates!
I put the 4 point harness in on the passenger side. Got the passenger door assembled and looking pretty. Got my initial tune done, 20psi and only 9* of timing for now. I need to learn how to control it before it gets the other 10psi and 6*. I dropped off a spare tranny to get rebuilt. I cut the fender flares off cause I was sick of them cutting my tires. I have new plastic flares that have not yet been installed. https://i.imgur.com/yPzTVfm.jpg https://i.imgur.com/IRd6XM1.jpg |
| All times are GMT -4. The time now is 12:28 PM. |
© 2024 MH Sub I, LLC dba Internet Brands